SICK OLS10 Скачать руководство пользователя страница 23

Страница: 23 / 48

Operation

8.1

Operating the sensor

8.1.1

Navigation

You can select a menu, parameter, option or value using the

and

pushbut‐

tons.

The menu path is specified in the relevant chapters of these instructions. → For the
overall menu structure and navigation, see

"Menu structure", page 45

8.1.2

Selecting an option

Select the desired parameter using the

and

pushbuttons.

Select the desired option using the

pushbutton.

Perform one of the following steps:
- Press the

pushbutton to save the change.

- Press the

pushbutton to cancel the process. The parameter name is dis‐

played again.

Perform one of the following steps to return to the default display:
- Press the

pushbutton repeatedly until the status indicator is displayed again.

- Wait for approx. one minute. The display will automatically switch back to the sta‐
tus indicator if no buttons are pressed. Any settings you have made will also be
saved.

8.1.3

Changing the value

Select the desired parameter using the

and

pushbuttons.

Press the

pushbutton. The current value of the parameter is displayed. The

first digit on the left flashes.

Press the

pushbutton to increase the digit. Press the

pushbutton to

decrease the digit.

Press the

pushbutton to save the digit entered. The next digit flashes.

Press the

pushbutton to cancel the process.

Repeat steps 3 and 4 until the last digit is saved. The parameter name is dis‐
played.

Press the

pushbutton repeatedly until the default display is displayed again.

Alternatively, you can wait for approx. one minute. The display will automatically
switch back to the default display if no pushbuttons are pressed.

8.1.4

Setting menu

The Setting menu – displayed as menSettng – is used to configure the sensor via the
parameters listed below.

To access the parameters in the Setting menu, press

then select the parameter

using

The available options are selected by pressing

and then

and confirmed with

OPERATION

8022017.10HG/2018-07-18 | SICK

O P E R A T I N G I N S T R U C T I O N S | OLS10

Subject to change without notice

Содержание OLS10

















































Результаты поиска

Содержание OLS10

Отзывы:

Похожие инструкции для OLS10

Бренды по названию

Популярные бренды

SICK OLS10, Руководство по эксплуатации

Результаты поиска

Содержание OLS10

Отзывы:

Похожие инструкции для OLS10

Бренды по названию

Популярные бренды