Shop fox W1852 Скачать руководство пользователя страница 42

Страница: 42 / 56

-40-

Model W1852 (For Machines Mfd. Since 11/17)

INTE

MAINTENANCE

Cleaning the Model W1852 is relatively easy. Vacuum excess

wood chips and sawdust, and wipe off the remaining dust

with a dry cloth. If any resin has built up, use a resin

dissolving cleaner to remove it.

Protect the unpainted cast-iron bed by wiping it clean after

every use—this ensures moisture from wood dust does not

remain on bare metal surfaces. Keep your bed rust-free

with regular applications of quality lubricants.

Cleaning.&.Protecting

Lubrication

For optimum performance from your machine, follow

this maintenance schedule and refer to any specific

instructions given in this section.

Ongoing

• Loose faceplate or mounting bolts.

•

Damaged center or tooling.

•

Worn or damaged wires.

• Loose machine components.

•

Any other unsafe condition.

Daily.Check

•

Clean off dust buildup.

•

Clean and lubricate lathe bed, spindle, and quill.

Monthly.Check

• Belt tension, damage, or wear.

• Clean out dust buildup from inside belt/pulley

cavity.

General

All bearings for the Model W1852 are lubricated and

sealed at the factory, and do not need additional

lubrication.

Wipe a lightly oiled shop rag on the outside of the

headstock spindle. DO NOT allow any oil to get on the

inside mating surfaces of the spindle.

Use the tailstock handwheel to extend the quill out to the

furthest position and apply a thin coat of white lithium

grease to the outside of the quill. DO NOT allow any oil or

grease to get on the inside mating surfaces of the quill.

MAKE. SURE. that. your. machine. is.

unplugged. during. all. maintenance.

procedures!. If. this. warning. is. ignored,.

serious.personal.injury.may.occur.

Tailstock

To disassemble the tailstock for cleaning,

loosen the set screw above the handwheel,

then completely unthread the handwheel

from the threads of the quill. Except for

the live center, thoroughly clean all of the

unpainted parts with mineral spirits and

apply a thin coat of light machine oil to

these surfaces.

When re-assembling the tailstock, thread

the handwheel back onto the quill, tighten

down the set screw that secures it, then

back the screw off one full turn so that the

handwheel can freely rotate.

Содержание W1852

























































Результаты поиска

Содержание W1852

Отзывы:

Похожие инструкции для W1852

Бренды по названию

Популярные бренды

Shop fox W1852, Руководство пользователя

Результаты поиска

Содержание W1852

Отзывы:

Похожие инструкции для W1852

Бренды по названию

Популярные бренды