background image

INSTALLATION 

 
The Supreme Finisher should be located on a flat, firm surface, in an area free of 
obstructions that could interfere with the safe operation of the equipment.  The Finisher 
should be positioned and leveled on a rubber mat to obtain quiet operation with a 
minimum of vibration. 
 
WARNING: 

All electrical work must be performed by a qualified electrician and 
must conform to all state and local ordinances. 

 
 

Do not, under any circumstance, tamper with, modify, or adapt the 
electrical plug and cord provided with this machine. 

 
ELECTRICAL CONNECTIONS 
 
Electrical connection may be made by either plugging the provided electrical cord into an 
appropriately wired electrical socket, or by wiring the machine directly into an electrical 
disconnect box. 
 
WARNING: 

If the electrical cord, plus or wiring should become frayed or 
damaged, replace it at once.  Do not attempt to operate the machine 
with faulty wiring as it could result in severe injury or death. 

 
NOTE: 

Refer to the machinery identification plate to determine the electrical 
specifications of this machine in respect to voltage, phase and 
amperage requirements. 

 
WARNING: 

Do not start Finisher before checking for proper sanding belt 
tracking. 

 

ELECTRICAL CONTROL BOX 

 
The electrical control box on top of the machine houses all motor controls on the Finisher.  
Each motor is automatically thermally protected.  In case of overload, the relay will trip 
and shut the motor off.  The overload will automatically reset in a short period of time. 

 

 

4

Содержание Supreme S-750



















Отзывы:

Похожие инструкции для Supreme S-750