background image

ACCESSORIES FOR SUPREME S-750 

7" PNEUMATIC CONTOUR SANDER (A-24) 
8" X 2" YARN BRUSH (A-2) 
8" HORSE HAIR WITH LEATHER BURNISHER (A-3) 
8" X 2" HORSE HAIR BRUSH BLACK OR BROWN (A-4) 
5" WIRE BRUSH (A-5) 
5" X 2" GRINDING STONE (A-6) 
FLAT WHEEL 3" DIAM. 1" WIDE 120 GRIT(A-7) 
6" FLAT EMERY WHEEL 120 OR 180 GRIT (A-8)  
8" X 2" LAMINATED CLOTH WHEEL (A-9) 
6" WELT BRUSH (A-10) 
PROTECTED EDGE SANDING WHEEL 1 3/8" X 4"(A-11) 
FS SANDING WHEEL 2 ½" X 5" (A-12)  
BOTTOM SANDING WHEEL 4 ½" WIDE (A-13) 
FS SANDING WHEEL 1 3/8" X 5" (A-16) 
B SANDING WHEEL 1 3/8" X 5" (A-17) 
NAUMKEAG HEAD (A-20) 
HEEL BREASTER FOR RIGHT OR LEFT SIDE (A-21 R OR L) 
1 ¼" X 2 ½" SANDING TUBE (A-22) 
3" X 4" WIDE EXPANDING WHEEL (A-1) 
8" X 1 SCOTCH BRITE WHEEL (A-25) 
8" X 2" SCOTCH BRITE WHEEL 
5" LAMINATED CLOTH WHEEL (A-30) 
8" X 2" FELT BURNISHER (A-31) 

STRAIGHT BAYONET THREADED ½" – 20 (A-32) 

STRAIGHT BAYONET THREADED 5/8" – 11 (A-33) 
CURVED LEATHER BURNISHER (A-34) 
8" DISCOUNT SANDER (A-35) 
CHANNEL WHEEL 1" THICK FOR BRACE GROOVE 
CARBIDE WHEEL 2" WIDE, AIR COOLING 
CARBIDE WHEEL 4" WIDE, AIR COOLING 
CHUCK DRILL 3/8" W/T KEY 
TRAUTMAN FITTING 3", THREAD 1/2-13 OR 5/8-11 (FOR S-240) 
TRAUTMAN FITTING 8", THREAD 1/2-13 OR 5/8-11 (FOR S-500) 
TRAUTMAN FITTING 12", THREAD 1/2-13 OR 5/8-11 (FOR S-240)

 

 

 

18

Содержание Supreme S-750



















Отзывы:

Похожие инструкции для Supreme S-750