background image

ACCESSORIES 

 
 
WARNING: 

Eye protection should always be worn by the operator and others in 
the work area when using the accessories supplied with the Supreme 
Finisher.  Eye protection is required for protection from flying debris 
and dust, which could cause eye injury. 

 

1 3/8” KEY WHEEL 

 

TO OPEN THE KEY WHEEL: 

 

1.

 

Insert wrench fully into the locking mechanism. 

 
2.

 

Grasp shaft with one hand and push down on wrench with other hand.  Wheel is in 
open position when the yellow brass piece opens, or separates from the small cam 
into which you have inserted the wrench. 

 
IMPORTANT:  IF WHEEL DOES NOT OPEN AFTER APPLYING PRESSURE 
DOWNWARD, USE THE PALM OF YOUR HAND TO SLAP DOWN THE WRENCH. 
 
 

This difficulty occurs when using heavier grit abrasives. 

 
TO APPLY ABRASIVE STRIP IN KEY WHEEL 
 
1.

 

Cut abrasive strip sufficiently long to fit into the open mechanism.  Be sure to leave 
a slight crown of about ¼” at the opening.   

 
DO NOT FEED ABRASIVE TOO TIGHTLY INTO MECHANISM, SINCE THE 
WRENCH WILL PULL ABRASIVE IN FOR YOU. 
 
BRUSHES ON QUICK CHANGE BAYONET FITTING 
 
The right end of the sanding shaft is machined to accommodate bayonet fitting (quick 
change).  Your brown and black brushes are installed on one of these.  Extra tools and 
sanding wheels are available on request.  See the list at the end of this book. 
 
When removing the quick change fittings, use the special spanner wrench supplied with the 
machine.  To remove, engage the spanner in the hole near the end of the bayonet fitting and 
apply a sharp rap downward.  Before putting on a fitting be sure the machine surfaces are 
clean.  Hand tightening is sufficient to hold the fitting in proper position. 
 
N.B.  When properly mounted, the sanding wheel adaptor will tighten itself by rotating it 
in the socket in the opposite direction of the sanding belt rotation. 
 
WELT BRUSH, STITCH PICKER AND EDGE IRON 

 

10

Содержание Supreme S-750



















Отзывы:

Похожие инструкции для Supreme S-750