Shira Trains D-10h Скачать руководство пользователя страница 2

THANK YOU FOR YOUR SUPPORT!  

This OPERATORS manual will cover the details of model that you have purchased, including how to service, repair 

and operate the functions on your new model.  Like all models, these models should be handled with care.  Our models 

are meant to be enjoyed with your eyes and ears, and should not be handled unless when needed; This isn’t because of 

faulty or shoddy construction, but so the oils on your hands do not settle on the boiler or other parts causing unsightly 

fingerprints.  There are also several small components on your model that could be jarred loose from over handling, 

and as such, let us reiterate,  it should always be handled with care -  in any service procedure or operations session. 

  The D-10h Locomotive features the following DIE-CAST parts: 

boiler, boiler support, tender chassis, leading truck centre weight, gear housing and internal fluid 

retainer casting.  Needless to say there is a lot of weight in your model due to the die-cast 

 Please take care that your locomotive does not come into contact with any live wires other than the 

intented powered track, this could lead to a disastrous outcome and is not covered by warranty.

SAFETY WARNING:

Your locomotive and tender has been checked at the factory and has had approx. 1 hour of run time 

already on it.  While we strive to find all the faults before they get out, we are only human.  Please 

check your locomotives operation on a test track to ensure that it is funtioning..  FAILURE TO DO 

SO MAY RESULT IN UNWANTED SHORTS OR LAYOUT DAMAGE WHICH WE CANNOT 

BE HELD RESPONSIBLE FOR AS WE HAVE NO CONTROL OVER THE ENVIRONMENT.

DIE CAST

DIE CAST

DIE CAST

DIE CAST

DIE CAST

DIE CAST

LED (WARM WHITE)

LED (WARM WHITE)

LED (WARM WHITE)

LED (RED)

CAPACITOR FOR KEEP ALIVE

SPEAKER

CONNECTING PORT

SUMMING BOARD

DCC PLUG

MOTOR

FET CONTROL FOR MOTOR

ELECTRICAL PICK UP

ELECTRICAL PICK UP

ELECTRICAL PICK UP

SMOKE CONTROL

SYNC-CAM

ACCESS HATCH

READ ME

Just like us, we are sure you hate reading manuals, but you should.  Really.  There is important 

stuff in here

Содержание D-10h











Отзывы: