Shinko SOVC-48CN1-RC7C Скачать руководство пользователя страница 6

Страница: 6 / 68

SHINKO- Tropical R410A High Efficient A5 Duct Technical Manual 50Hz

Product features

Indoor Unit

General

These duct type indoor units which capacity range is from 4ton to 5ton, are suitable for

mounting above ceiling. The units are factory assembled, internally wired and tested before

leaving the manufacturer. The indoor units are insulated by polyethylene foam.

Casing

The units are constructed form Heavy Gauge Zinc coated steel sheets. The sheet steel zinc

coated by hot dip process conforming to standard ASTM A653.

Evaporator

Internally finned, copper tubes mechanically bonded to a configured hydrophilic aluminum fin

shall be standard. Coils are leak tested at the factory to ensure the pressure integrity. The

evaporator coil is already leak tested to 3,100kPa (450 psig). Anti-corrosion treatment for coils is

optional.

Drain pan

The condensate drain pan is fabricated of EPS. The inner of the drain pan adopts vacuum

forming technology.

Indoor fan

The indoor units have centrifugal fan. The fan is directly driven by indoor fan motor.

Filter

The filter is already fix in the frame of air return. It is Nylon washable type.

Outdoor unit

General

The outdoor units are top-discharge type. The units with weatherproof heavy gauge base are

factory assembled, internally wired, fully charged refrigerant and 100% run tested to check

cooling operation, fan rotation and control sequence before leaving the factory.

Содержание SOVC-48CN1-RC7C





































































Результаты поиска

Содержание SOVC-48CN1-RC7C

Отзывы:

Shinko SOVC-48CN1-RC7C, Техническое руководство, Страница: 6 / 68

Результаты поиска

Содержание SOVC-48CN1-RC7C

Отзывы: