Shinko SOVC-48CN1-RC7C Скачать руководство пользователя страница 29

Страница: 29 / 68

SHINKO- 4

5 ton High Efficiency A5 Duct Technical Manual

reported immediately to the service agent.



When handling the unit, take into account the following:

✓

Fragile, handle the unit with care.

✓

Move the unit as originally package as possible.

✓

When lifting the unit, always use protectors to prevent belt damage and pay attention to the

position of the unit’s center of gravity.

Installation of the Indoor Units

2.1 Installating indoor units



As the following picture, when install the indoor unit, select the enough solid and level site with

enough space for installation and maintenance.



The inspection orifice should be enough larger to repair and maintenance the unit.



Ensure that the minimum drain gradient is over 1/100.



Please refer to the following figure for the distance measurement between the screw bolts.



Please install with screw bolts. Use

Ф10 or bigger screws.



The handling to the ceiling varies from constructions consult the construction personnels for the

specific procedures.



Cut off the roof beam. Strengthen the place cut off, and consolidate the roof beam.



Carry out the pipe and line operation in the ceiling after finishing the installation of the main body.

While choosing where to start the operation, determine the direction of the pipes to be drawn out.

Especially in case there is a ceiling, position the refrigerant pipes, drain pipes, indoor and outdoor

lines to the connection places before hanging up the unit.

Содержание SOVC-48CN1-RC7C





































































Результаты поиска

Содержание SOVC-48CN1-RC7C

Отзывы:

Shinko SOVC-48CN1-RC7C, Техническое руководство, Страница: 29 / 68

Результаты поиска

Содержание SOVC-48CN1-RC7C

Отзывы: