background image

 

15

  Danger : Suffocation from exhaust fume 

z

  Exhaust fume from the engine contains many elements harmful to human. Do not operate 

this equipment in poorly ventilated area, such as inside a room or in a tunnel. 

 

Caution : Suffocation from exhaust fume 

z

  Do not point the exhaust fume toward pedestrians or building. 

 

Caution : Fire 

z

  Temperature around muffler and exhaust can get extremely high. Keep any inflammable 

items (such as fuel, gas, paint, etc.) away from the equipment. 

z

  Always operate this equipment on flat surface and, at least 1 meter away from any objects 

(wall, box, etc.) 

             

Caution : Injuries 

z

  Always place the equipment on flat and stable surface, to keep the equipment from sliding. 

Be sure to lock the wheels for the wheeled models. 

z

  When starting the engine, turn off the connected equipment and set the circuit breaker to 

OFF position. 

  Turn the circuit breaker to OFF position. 

  Turn the fuel lever to OPEN. 

  Turn the Slow-Down switch to ON. 

  When the temperature is below 5

℃,

turn the starter 

switch to PREHEAT. The preheating lamp flashes 15 

seconds. The lamp comes off when the PREHEAT fin-

ishes. 

  Turn the starter switch to START to start the engine by the 

starter motor. 

         <Caution> 

z

  Do not drive the starter motor for more than 15 seconds successively. 

z

  If you need to restart, wait for 30 seconds or more before retry. 

  Release the starter switch, as soon as the engine is started. 

<Caution> 

z

  Once the engine is started, do not turn the starter switch to START. 

  Make sure the frequency to the monitor on the control panel. 

  Keep the engine idle for about 5 minutes.     

   

 

 
 

 

 

 

 

 

       

FUEL LEVER

 

CLOSE

 

OPEN

 

SLOW-DOWN SWITCH

 

STARTER SWITCH

 

PREHEAT LAMP

CIRCUIT BREAKER

 

 DGW311DM  

PREHEAT LAMP

 

STARTER SWITCH

 

SLOW-DOWN SWITCH

 

CIRCUIT BREAKER 

 DGW311L  

Содержание DGW311DM






































Отзывы: