Shindaiwa C254 страница 19 Скачать руководство пользователя

Страница: 19 / 32

Engine

Cover

Screws

Engine Cover

Muffler

Muffler Gasket

Muffler Bolts

Spark Arrester Screen

Spark Arrester Cover

Cover Screws

Muffler and spark arrester maintenance

With a 3 mm hex wrench remove the

engine cover screws and the engine

cover.

If the engine becomes sluggish and low

on power, check and clean the spark

arrester screen.

IMPORTANT!

If you note excessive carbon buildup,

consult with an authorized servicing

dealer.

WARNING!

Never operate the unit with a

damaged or missing muffler or spark

arrester! Operating with a missing or

damaged spark arrester is a fire hazard

and could also damage your hearing.

With a 4 mm hex wrench, remove the

3 muffler bolts and the muffler.
With a small flat bladed screwdriver

remove the 2 screws holding the

spark arrester screen and cover to the

muffler.

Remove the screen and clean it with a

stiff bristle brush.
Inspect the cylinder exhaust port for

any carbon buildup.
Reassemble the spark arrester, muf-

fler and engine cover in the reverse

order of disassembly.

Maintenance

(continued)

NOTE:

Every unit is run at the factory and the carburetor is set in compliance with

emission regulations. Carburetor adjustments, other than idle speed, must be

performed by an authorized Shindaiwa dealer..

Carburetor Adjustment

Engine Break-In

New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be

made. During the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can

be adjusted as required.

High Altitude Operation

This engine has been factory adjusted to maintain satisfactory starting, emission, and durability performance up to

1,100 feet above sea level (ASL) (96.0 kPa). To maintain proper engine operation and emission compliance above

1,100 feet ASL the carburetor may need to be adjusted by an authorized Shindaiwa service dealer.

IMPORTANT!

If the engine is adjusted for operation

above

1,100 feet ASL, the carburetor

must be re-adjusted when operating the engine

below

1,100 feet ASL, oth-

erwise severe

engine damage may result.

Содержание C254

































Результаты поиска

Содержание C254

Отзывы:

Похожие инструкции для C254

Бренды по названию

Популярные бренды

Shindaiwa C254, Руководство владельца/оператора

Результаты поиска

Содержание C254

Отзывы:

Похожие инструкции для C254

Бренды по названию

Популярные бренды