Shindaiwa C254 Скачать руководство пользователя

Страница: 17 / 32

Remove and inspect the pre-filter.

If the pre-filter is torn or otherwise

damaged, replace it with a new

one.

Clean the pre-filter with soap and

water. Let dry before reinstalling.

Inspect the air filter element. If the

element is damaged or distorted,

replace it with a new one.

Tap filter gently on a hard surface to

dislodge debris from element or use

compressed air from the inside to blow

debris out and away from the air filter

element.

Install the air filter element, pre-filter

and cover in the reverse order of

removal.

Remove and inspect spark plug

spark plug gap--all models

0,6 mm

Clean the spark

plug and check

the gap at the

electrode.

Components of air filter

Filter element

Prefilter

Loosen

fasteners

Remove the cover of the air filter

50-hour maintenance

CAUTION!

Before removing the spark plug,

clean the area around the plug to

prevent dirt and debris from getting

into the engine’s internal parts.

10/15-Hour maintenance

Maintenance

(continued)

10-Hour maintenance

(more frequently in dusty

conditions)

Remove the air filter cover by loos

ening the cover screw(s) and lifting.

IMPORTANT!

Direct the air stream at the inside face

of the filter only!

CAUTION!

Never operate the unit if the air

cleaner assembly is damaged or

missing!

Remove and clean or replace the

spark plug.

Clean the spark plug. Adjust elec-

■

trode gap according to the values

listed in the ”Specifications” section. If

the spark plug must be replaced, use

only the type recommended in ”Spec-

ifications” or equivalent resistor type

spark plug of the correct heat range.

Gearcase lubrication

1. Clean all loose debris from gear box.

2. Remove plug (A) and check level of grease. Grease should fill gear case

to bottom of grease plug hole.

3. Add grease if necessary using manual grease gun or squeeze-type tube.

Do not use high pressure grease gun. DO NOT over-fill.

Содержание C254

































Результаты поиска

Содержание C254

Отзывы:

Похожие инструкции для C254

Бренды по названию

Популярные бренды

Shindaiwa C254, Руководство владельца/оператора

Результаты поиска

Содержание C254

Отзывы:

Похожие инструкции для C254

Бренды по названию

Популярные бренды