background image

-

8 -

(4) Screen change within mode 1 screen group

Two methods are used for screen change within mode 1 screen group.

One is to press the 

key as shown on above mode 0 screen group.

The other is to mode the screen directly by indicating screen No. on the top direct call screen.

Example: Direct calling the screen No.8 PV bias value set screen

(5) Selecting and setting digit to change of mode 2 screen

When mode 2 screen is displayed, the point of selectable digit flashes.

By pressing 

key, the selectable digit (digit whose point is flashing) moves.

In case of changing the set value, flash the point to be changed with 

key, 

select data with the 

keys and press 

key again to register the set value and move selectable digit.

Example: changing the control output characteristics from 

(heating) to 

(cooling)

*  "." on the screen shows the selectable digit (digit whose point is flashing).

(6) Shifting setting items on input scaling screen of mode 2 screen group and setting method

Pressing the 

key on the function selecting screen calls the input scaling screen onto the display. The decimal point in the rightmost position on

the top row flashes.

Press the 

or 

key to change the lower limit value and press the 

key to register the data.

Upon registering the lower limit value data, the decimal point in the rightmost digit in the botton row begins to flash. Change the higher limit

value by pressing the 

or 

key and register it by means of the 

key.

Upon registering the higher limit value data, the decimal points in the rightmost digits of the bottom and top rows flash. Change the positions of

the decimal points by pressing the 

or 

key and register it by means of the 

key.

Each time the 

key is pressed, the flashing decimal point in the rightmost digit moves from the top row 

bottom row 

top and bottom rows

top row 

.

In case the lower limit value and the higher limit value are set to produce a difference which is less than 10 counts or more than 5000 counts, the

higher limit value is forced to change to +10 or +5000 counts. The higher limit cannot be set to be less than a lower limit value +10 counts or

more than a lower limit value +5000 counts.

NOTE: In case of changing data and pressing 

key longer than 5 seconds, the screen moves to mode 0 basic screen without a data 

registration. It requires a data verification with 

key and screen change.

4-3. Screeen configuration

In the SR70 series controller, the screen configuration is divided into screen groups and screens corresponding to the frequency of usage in their
operation.

(1) Mode 0 screen group

It is made up of screens of relatively high frequency in use for operation, i.e., the basic screen (for setting target value and confirming current
measured value), the auto tuning action control screen and the alarm setting screens.

(2) Mode 1 screen group

Made up of screens of less frequency than those of mode 0 group, i.e., screens for setting values to be changed as required by input conditions or
control capability and a screen for locking items not to be changed.

(3) Mode 2 screen (function slecting screen)

Once items are set in this screen, the need to change them seldom arises; selected code of measuring range, selected output characteristic, slected type
of optional alarm functions, and selected action mode of heater break alarm are displayed on this single screen.

(4) Method of changing data

Press the 

or 

key to change data in each screen and press the 

key to register the changed data.

1-0 direct call screen

1-0 direct call screen

1-8 PV bias value set screen

key

key

several times

point flashes

key

key

key

Содержание SR70 Series

















Отзывы: