ENGLISH
Operations
LISTENING TO A PROGRAM SOURCE
Before operation
• Enter the standby mode.
• The STANDBY indicator lights up.
This means that the receiver is not disconnected from the
AC mains and a small amount of current is retained to
support the operation readiness.
• To switch the power off, push the POWER switch again.
• Then the power is cut off and the STANDBY indicator
goes off.
• Each time the POWER ON/STANDBY button on the front panel is
pressed, the receiver is turned on to enter the operating mode or off
to enter the standby mode.
• On the remote control, press the POWER ON button to enter the
operating mode or press the STANDBY button to enter the standby
mode.
POWER
ON
OFF
ON / STANDBY
1.
In the standby mode, turn the power on.
3.
Select the desired input source.
14
■
Note :
Before operating this receiver, first set this unit as desired for optimum performance, doing the system setup
procedures. (For details, refer to "System Setup" on page 37.)
• Then “SPEAKER ON” is displayed and the sound can be heard from
the speakers connected to the speaker terminals.
• When using the headphones for private listening, press the
SPEAKER button again to switch the speakers off (“SPEAKER OFF”
is displayed).
2.
Switch the speakers on.
• Each time the “VIDEO” button on the front panel is
pressed, the input source changes as follows:
→
VIDEO 1
→
VIDEO 2
→
VIDEO 3
• Each time the “AUDIO” button on the front panel is
pressed, the input source changes as follows:
→
CD
→
AUX 1
→
TV*
→
AUX 2
→
TAPE
→
NET/USB
→
TUNER
(Frequency display)
* : Only when the HDMI CONTROL is set to ON, you can
hear the digital audio signals from TV via a HDMI cable.
(For details, refer to “When selecting the HDMI
CONTROL” on page 50.)
• When selecting NET/USB, refer to “LISTENING TO
INTERNET RADIO BROADCASTS, MUSIC FILES” on
page 26.
• Each time the BAND button(or the TUNER button on the
remote control) is pressed, the band changes as follows:
→
FM STEREO
→
FM MONO
→
AM
When CD, VIDEO 1 ~ 2 is selected as an input source
AUDIO ASSIGN
RETURN
4.
Select the digital or the analog input connected as
desired.
• Each time this button is pressed, the corresponding input
is selected as follows:
→
OPT
→
COAX.1
→
COAX.2
→
ANALOG
■
Notes :
• When the HDMI IN connector is connected to your video
component, you cannot assign the audio input as desired.
(It means that only the HDMI digital audio signals can be
heard.)
• When the HDMI IN connector is not connected (and the
“HDMI” indicator flickers), you can assign the audio input.
• When VIDEO 3, AUX 1, AUX 2, TAPE, TV, NET/USB or
tuner is selected as an input source, the signal input cannot
be selected.
• When the selected digital input is not connected, the
“D(Digital)” indicator flickers and the analog input is
automatically selected.
• The selected digital input or analog input is automatically
assigned to the corresponding input source on the INPUT
setup menu. (For details, refer to “SETTING THE INPUT
SETUP” on page 41.)
• The sound from the component connected to the selected
digital input can be heard regardless of the selected input
source.
INPUT
BAND
AUDIO
VIDEO
■
Auto Power Save
• The auto power save is a function that automatically turns the
power off to enter the standby mode. When any button is not
pressed for more than the time you set, it will function. (For details,
refer to “When selecting the AUTO POWER SAVE” on page 39.)
RD-606i(G)_ENG_110511_RD-606i(G)_ENG 2011-05-13 오전 9:57 페이지 14
