Sharp ViewcamZ VL-Z500E-S страница 18 Скачать руководство пользователя

Страница: 18 / 127

Preparation

Charging the Battery
Pack

Attach the battery pack to the
camcorder, and make sure that the
Power switch is set to OFF.

Connect the supplied power cord to
the AC power socket on the AC
adapter, and insert the AC plug into a
power outlet.

Insert the DC plug into the DC IN
jack of the camcorder.

• The POWER/CHARGE (RED)

indicator lights up red.

• The POWER/CHARGE (RED)

indicator turns off when the battery is
charged.

Remove the DC plug from the DC IN
jack, then remove the AC adapter
from the power outlet.

• The chart specifies the approximate times in

minutes.

Notes:

•

Charge the battery pack between 10°C and
30°C. The battery pack may not charge
properly at temperatures too low or too
high.

•

The battery pack and AC adapter become
warm during charging. This is not a
malfunction.

•

Using the zoom (see page 24) and other
functions or turning the power on and off
frequently will increase power consump-
tion. This may result in a decrease in the
actual recording time compared to the
maximum continuous recording time listed
above.

•

The charging time and recording time may
vary depending on the ambient tempera-
ture and the condition of the battery pack.

• See pages 102 and 103 for more information

on using the battery pack.

• Charge only SHARP model BT-L227 battery

packs. Other types of battery packs may
burst, causing personal injury and damage.

• When attaching the supplied audio/video/S-

video cable or USB cable, remove the DC
plug, open the terminal cover and connect it.

BT-L227

Charging

time

Battery

pack

Max.

continuous

recording time

Max.

continuous

playback time

on LCD

120

145

125

Charging time and maximum
continuous recording and playback
times in Tape modes

LCD

closed

LCD

open

125

AC power socket

To power

outlet

DC plug

DC IN jack

POWER/CHARGE (RED)

indicator

VL-Z500E-E-006-021

04.2.17, 9:17 AM

Содержание ViewcamZ VL-Z500E-S
































































































































Результаты поиска

Содержание ViewcamZ VL-Z500E-S

Отзывы:

Похожие инструкции для ViewcamZ VL-Z500E-S

Бренды по названию

Популярные бренды

Sharp ViewcamZ VL-Z500E-S, Руководство по эксплуатации

Результаты поиска

Содержание ViewcamZ VL-Z500E-S

Отзывы:

Похожие инструкции для ViewcamZ VL-Z500E-S

Бренды по названию

Популярные бренды