VL-E610S/VL-E610H
VL-E660S/VL-E96E
VL-E98E
3-10
3-5. ADJUSTING THE Y/C, AUDIO AND LCD CIRCUITS ON MODELS WITHOUT A/V IN MODE
(A/V IN MODE SET-UP PRODUCE)
1) Set the switch of main body to VCR, and use the remote control (RRMCG0033TASA) for adjustment to turn on the
adjustment mode.
2) Set up the adjustment address (example : EEmode adjustment address 14). Once this address has been set up, the A/V
IN mode (test mode) is automatically brought and the images appear on the LCD display.
3) Now make the adjustments referring to the instruotions in the manual.
3-4. INITIAL SETTING OF E
2
PROM IC
3-4-1. E
2
PROM data alterable ways
1) Set the switch of main body to VCR, and use the remote control (RRMCG0033TASA) for adjustment to turn on the
adjustment mode.
2) VCR adjustment address setting.
V ADJ
00
“00” is blinking
After an objective address was established, play key is pushed and set.
In addition, numerical change uses a “REW” or “FF” key.
3) VCR adjustment data setting.
V ADJ
00 ##
Value of “##” differs by an address.
After an objective data was established, “PLAY” key is pushed and set.
4) When data of other address are changed successively, push “STOP” key, and please repeat operation to 5) from 3).
5) When SW of the substance is turned into off, data are written to E
2
PROM from systematic microcomputer.
3-4-2. IC702 (E
2
PROM)
When the IC702 has been replaced, make the following settings and adjustments.
1. Remove the backup battery (CR2025)
2. Turn power switch to CAMERA
3. Setting up the V ADJ mode as follows.
* After press the CONTINUE key, press the VCR ADJ key on service remote control (RRMCG0033TASA).
E610S
E610H
E660S
E96EX
E98EX
address
data
data
data
data
data
02
0A
0A
0A
0B
0B
0A
F5
F5
F5
F4
F4
03
80
88
B0
88
FA
0B
7F
77
4F
77
05
05
00
00
00
40
40
0D
FF
FF
FF
BF
BF
01
00
00
00
00
00
04
00
00
00
00
00
4. After setting the above data, clear the V ADJ mode and turn off the power by pull out the battery pack or DC cable.
Neglect about 30 seconds after turned of power, because data of address becomes effective after microcomputer is
reset.
Now the setting of data is completion.
Adjustments to follow
Make the system controller servo, VCR, and LCD adjustments according to their respective instructions.
3-4-3. CAMERA ADJUSTMENT
When the IC2 has been replaced, make the camera adjustment according to its instructions.
All the camera adjustment data are written in the E
2
PROM provided on the lens unit. Therefore, when the lens is replaced,
the camera must be adjusted again according to the camera adjusting procedure.
Содержание ViewCam VL-E610S
