4-13
Cutting status display & setup
When cutting is in operation, press
to enter cutting status display and setup page.
Or
Page 1
–
cutting status display 1
This page shows the following information (from
top to bottom):
Feeding length (current feeding vise position)
Blade speed
Deviation value (optional)
Current in ampere (optional)
Spray Run / Stop Second Count (optional)
Number of current cutting job/step in operation
Preset quantity of current cutting job
Number of cuts finished
Error messages (highlighted in yellow; can be
cleared by pressing down for three seconds)
Press Home to return to the main control menu.
Press NEXT to go to the next setup page.
The green square light on the bottom left corner
indicates the warranty status of the HMI touch
screen. Warranty is one year and starts counting
after 70 hours of operation after the machine is
shipped. Warranty status light turning to red
indicates the HMI touch screen has expired.
Page 2
–
cutting status display 2
This page comes in two versions depending on if the
optional blade deviation detector is installed on the
machine. The shared features are as follows:
Current blade life in hours
Error message (bottom of page)
Cut Piece Reset - Reset all
Cuts Finished
data by
pressing this button for three seconds.
Note:
If you start a new set of program without
clearing cutoff data from previous job, the first cut (trim
cut) will be skipped as the second program is deemed as
the succeeding part of the previous program.
All Reset - Reset all preset cutting data within
Starts Step
and
Ends Step
by pressing this button
Содержание SW-180NC
