Sharp SF-2540 Скачать руководство пользователя страница 10

Страница: 10 / 104

MAKING COPIES

Normal copying

NORMAL COPYING

●

For manual copy density adjustment, press the EXPOSURE
key to select MANUAL and adjust with the LIGHT and DARK
keys as desired.

●

For photographs, select PHOTO and then adjust with the
LIGHT and DARK keys as desired.

Use the 10-key pad to enter the desired number of
copies.

●

The number will be shown in the copy quantity display.

●

A single copy can be made with the initial setting, i.e., when “0”
is displayed.

●

Use the clear (

) key to cancel an entry if a mistake is

made.

Press the START key.

●

The number in the copy quantity display will decrease by 1
each time a copy is made.

●

To cancel a copy run, press the CLEAR ALL (

) key.

Copying will stop and the number in the copy quantity display
will be reset to 0.

●

To repeat the same copy sequence for a different original,
simply replace the original and press the START key.

1 0 0 %

COPY RATIO

EXPOSURE

MANUAL

LIGHT

DARK

1 0 0 %

COPY RATIO

EXPOSURE

PHOTO

LIGHT

DARK

INFORMATION

INTERRUPT

CLEAR ALL

START

AUDIT CLEAR

START

Содержание SF-2540









































































































Результаты поиска

Содержание SF-2540

Отзывы:

Похожие инструкции для SF-2540

Бренды по названию

Популярные бренды

Sharp SF-2540, Руководство по эксплуатации

Результаты поиска

Содержание SF-2540

Отзывы:

Похожие инструкции для SF-2540

Бренды по названию

Популярные бренды