background image

 

SERVICE MANUAL

Parts marked with "

" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the

safety and performance of the set.

This document has been published to be used for
after sales service only.
The contents are subject to change without notice.

CHAPTER 1. SPECIFICATION

[1] SPECIFICATION............................................ 1-1
[2] EXTERNAL 

DIMENSION............................... 1-3

[3] WIRING 

DIAGRM .......................................... 1-4

[4] ELECTRICAL 

PARTS .................................... 1-5

CHAPTER 2. EXPLAMATION OF CIRCUIT AND OP-
ERATION

[1] BLOCK 

DIAGRAMS....................................... 2-1

[2]  MICROCOMPUTER CONTROL SYSTEM.................. 2-3
[3] FUNCTION..................................................... 2-7

CHAPTER 3. FUNCTION AND OPERATION OF PRO-
TECTIVE PROCEDURES

[1]  PROTECTION DEVICE FUNCTIONS AND 

OPERATIONS ................................................ 3-1

[2]  AIR CONDITIONER OPERATION IN 

THERMISTOR ERROR ................................. 3-3

[3] THERMISTOR 

TEMPERATURE

CHARACTERISTICS ..................................... 3-5

[4]  HOW TO OPERATE THE OUTDOOR 

UNIT INDEPENDENTLY ................................ 3-5

[5]  GENERAL TROUBLESHOOTING CHART ................. 3-6

[6] MALFUNCTION 

(PARTS) 

CHECK

 METHOD ......................................................3-8

[7]  OUTDOOR UNIT CHECK METHOD........... 3-11
[8] TROUBLESHOOTING 

GUIDE ....................3-14

[9] CHART ........................................................3-15

CHAPTER 4. REFRIGERATION CYCLE

[1] SCHEMATIC 

DIAGRAM ................................4-1

[2] STANDARD 

CONDITION ..............................4-1

[3]  TEMPERATURE AT EACH PART AND 

PRESSURE IN 3-WAY VALVE ......................4-1

[4] PERFORMANCE 

CURVES...........................4-2

CHAPTER 5. DISASSEMBLING PROCEDURE

[1] INDOOR 

UNIT...............................................5-1

[2]  HOW TO REMOVE PLASMACLUSTER 

UNIT
(For the models with PLASMACLUSTER)..................5-4

[3]  DISASSEMBLY OF OUTDOOR UNIT...........5-5

Parts Guide

TopPage

CONTENTS

No. S2005AYXP12LST

SPLIT TYPE
AIR CONDITIONER

MODEL

INDOOR UNIT

AY-XP9LSR
AY-XP12LSR

OUTDOOR UNIT

AE-X9LSR
AE-X12LSR

In the interests of user-safety (Required by safety regulations in some countries)  the set should
be restored to its original condition and only parts identical to those specified should be used.

AYXP9LSR

Содержание Plasmacluster AE-X12LSR





























































Отзывы: