MD-MT821/W
– 6 –
Many potential “problems” can be resolved by the owner without calling a service techni-
cian.
If something seems to be wrong with this product, check the following before calling your
authorised SHARP dealer or service centre.
PROBLEM
CAUSE
The unit does not turn
on.
●
Is the A
C
adaptor disconnected?
●
Is the battery exhausted?
●
Is the unit in the hold mode?
●
Has condensation formed inside the unit?
●
Is the unit being influenced by mechanical shock or by
static electricity?
●
Is the volume set too low?
●
Is the remote control unit or the earphones plugged in?
●
Are you trying to play a MiniDisc with data on it instead
of a MiniDisc containing music?
●
Is the unit in the hold mode?
●
Is the battery exhausted?
●
Is the remote control unit plug or the earphone plug in-
serted firmly?
●
Is the battery exhausted?
●
Is the unit being subjected to excessive vibration?
●
Has the track number or character information been
written on the disc yet?
●
Is the unit in the recording or editing mode?
●
Is the MiniDisc protected against accidental erasure?
●
Is the unit connected properly to the other equipment?
●
Is the A
C
adaptor unplugged or did a po
w
er f
ailure
occur whilst recording or editing?
●
Is the unit in the hold mode?
●
Is an optical signal being output from the external
equipment?
Read the operation manual for the external equipment.
No sound is heard from
the earphones.
When the operation
buttons are pressed, the
unit does not respond.
Some sounds are
skipped.
The MiniDisc cannot be
ejected.
Recording and editing
are impossible.
■
If trouble occurs
When this product is subjected to strong
external interference (mechanical shock,
e
xcessiv
e static electr
icity
, abnor
mal sup-
ply voltage due to lightning, etc.) or if it is
oper
ated incorrectly
, it ma
y malfunction.
If
such a problem occurs, do the following:
1
.
Unplug the A
C
adaptor from the A
C
socket.
2.
Remo
v
e
the batter
y.
3
.
Leave the unit completely unpowered for
approximately 30 seconds.
4.
Plug the A
C
adaptor bac
k into the A
C
socket and retry the operation.
If strange sounds, smell or smoke come out
of the unit or an object is dropped into the
unit, remo
v
e
the A
C
adaptor from the A
C
socket immediately and contact an
authorised SHARP service centre.
TROUBLESHOOTING
■
Moisture condensation
In the following cases, condensation
may form inside the unit.
●
Shor
tly after tur
ning on a heater
.
●
When the unit is placed in a room where
there is excessive steam or moisture.
●
When the unit is moved from a cool
place to a warm place.
When the unit has condensation
inside, the disc signals cannot be
read, and the unit may not function
pr
operly
.
●
If this happens, remove the disc.
The condensation should evaporate in
appro
ximately 1 hour
. The unit will then
function proper
ly
.
When the number of tracks used
reaches the limit, regardless of the
remaining recording time, further
recording will be impossible.
(Maximum number of tracks: 255)
If a MiniDisc has been recorded or
edited repeatedly or if a MiniDisc has
scratches on it, it may not be possible
to record the maximum number of
tracks on it.
If there are scratches on a disc, the unit
will automatically avoid recording in
those areas
. The recording time will be
reduced.
When the remaining recording time of
a disc is displayed, short tracks less
than 12 seconds long may not be
included in the total.
For MiniDiscs on which repeated
recording and editing operations were
performed, the COMBINE function
may not work.
A cluster (about 2 seconds) is normally
the minimum unit of recording. So, even
if a track is less than 2 seconds long, it
will use about 2 seconds of space on the
disc.
Therefore, the time actually available for
recording may be less than the
remaining time displayed.
If there are scratches on discs, those
sections will be automatically avoided
(no recording will be placed in those
sections).
Theref
ore
, the recording time
will be reduced
.
For MiniDiscs on which repeated
recording and editing were performed,
some sounds may be skipped whilst
cueing and reviewing.
If there are scratches or dust on a
MiniDisc, the track numbers following
that track will be increased by one.
MINIDISC SYSTEM LIMIT
A
TIONS
MiniDiscs are recorded using a diff
erent system than is used f
or cassette tapes or D
A
T
recordings
.
Theref
ore, the f
ollo
wing conditions ma
y be encountered, depending on ho
w
the disc has been recorded or edited.
These are due to system limitations
, and should be
considered normal.
Even if the maximum recording
time of a MiniDisc has not been
reac
hed,
“DISC FULL
”
or
“T
OC
FULL” may be displayed.
Even if the number of tracks and
the recording time have not
reached the limit, “DISC FULL”
may be displayed.
Even if several short tracks are
erased, the remaining recording
time may not show an increase.
T
w
o trac
ks ma
y not be combined
in editing.
The total of the recorded time and
time remaining on a disc may not
add up to the maximum possible
recording time.
When recorded tracks are played
back using the cue and review op-
erations, some sounds may be
skipped.
A track number can be created in
the middle of a track.
Содержание MD-MT821(GL)
Страница 51: ...MD MT821 W M E M O 8 ...
