Sharp MD-MT821(GL), Руководство по обслуживанию

Страница: 5 / 52

MD-MT821/W
– 5 –
OPERATION MANUAL
POWER SOURCE
■
Rechargeable battery power
This unit can be used with 4 diff
erent po
wer sources:
a rechargeab
le batter
y,
an A
C
adaptor
, a batter
y case
, and a separ
ately av
ailab
le car adaptor (AD-CA20X).
When the rechargeable battery is used for the first time or when you want to use it af- ter a long period of disuse, be sure to charge it fully
.
1
Open the rechargeable battery compart- ment co
v
e
r.
2
Inser
t the rechargeab
le batter
y.
●
Insert the side with the arrow first.
3
Close the rechargeable battery compart- ment co
v
e
r.
4
Plug the A
C
adaptor into the A
C
soc
ket,
and then inser
t the plug on the A
C
adap-
tor lead into the DC IN 5V socket.
●
About 4 seconds later
,
“
”
will
flash, and the battery will begin charg- ing.
●
Battery charging will be complete in 3.0 hours. When the charging is com- plete, “
” will go out.
Notes:
●
After charging has been completed, the AC adaptor may be left connected. (For example, when charging at night)
●
If the rechargeable battery is in the unit, it will be charged, even whilst operating the unit. (Float charge)
●
Do not force open the rechargeable bat-
tery cover too wide.
●
When the A
C
adaptor plug is inser
ted
and a MiniDisc has already been in- ser
ted, pla
ybac
k ma
y star
t automatically
.
In this case, press the
■
/ :OFF button
twice to tur
n the po
wer off
.
1 2 4
OPEN
OPEN
OPEN
OPEN
OPEN
Mark
A
C
110-240V
, 50/60 Hz
T
o
the DC IN 5V soc
k
e
t
Inser
t securely
, all the
way in.
CONVENIENT OPERA
TION OF
THE UNIT
■
Checking the remaining
amount
of battery charge
The remaining amount of battery charge is shown by the battery indicator (
)
during operation. < How to read the battery indicator >
●
When the battery is completely discharged, the whole battery indicator will flash. Re- charge the battery or replace the alkaline battery with a new one.
●
When the battery has run completely out, “BA
TT EMPTY”
(main unit) and
“Lo BA
TT”
(remote control unit) will appear
. Then, the
po
w
er will be disconnected automatically
.
Notes:
●
When using the unit with an alkaline bat- ter
y or a rechargeab
le batter
y,
the batter
y
indicator will not correctly display the remain-
ing capacity for approximately 20 seconds after the power has been turned on.
●
When the A
C
adaptor included with this unit
or a separately available car adaptor is used, the battery indicator will not be shown.
●
The number of bars shown in the battery indicator may increase or decrease, de- pending on the operation being performed. This is normal.
●
When the rechargeable battery and the al- kaline battery are used at the same time, the rechargeable battery is used first, then the alkaline batter
y.
Since the battery indicator shows the re- maining amount of the particular battery being used, the number of bars will in- crease when the unit switches to the al- kaline batter
y.
Battery indicator
When the battery needs charging, it is impossible to start recording or editing.
When the battery is completely charged
Charging is needed.
RECORDING USING
THE OPTICAL DIGIT
AL CABLE
There are cases where digital recording may be impossible.
In the following cases digital recording is impossible, even if you are using digital cables. When you attempt to make a new digital recording from a track that was digitally re- corded on a MiniDisc.
●
MiniDiscs are designed so that only first
generation digital copies can be made. Further digital copies are prevented by the SCMS (Serial Copy Management System).
Playback
Digital cable
CD pla
y
e
r,
MD
pla
y
e
r,
etc.
Digitally recorded MiniDisc
Analogue recording is possible.
Recording
Playback
Digital cable
Recording