Sharp AX-1100, Руководство по обслуживанию

Страница: 16 / 56

AX1100(R)
6 – 3
[2] Operation of electric parts in each heating mode
[3] OFF CONDITION
1. When the oven is plugged in with the door closed, the line voltage is supplied to the noise filter. And the display shows nothing.
2. When the door is opened with plugged in, the contacts (COM-NC) of the monitored interlock switch is closed. And the line voltage is supplied to
the T/C transformer and the control unit. Then the contacts of the relay RY-9 are closed and the contacts of the relay RY-1 are closed. And the
oven lamp is turned on.The display shows “0.”.
3. When the door is closed, the contacts (COM-NC) of the monitored interlock switch are opened. Because the contacts of the relay RY-9 have been
closed, the line voltage is kept supplying to the T/C transformer and the control unit. But the contacts of the relay RY-1 are opened and the oven
lamp is turned off.
Energy save mode
If the door is closed and any key is not pressed for more than 3 minutes except for the following 10 conditions, the contacts of the relay RY-9 will be
opened and the control unit will be not energized. Open and close the door, the control unit will resume.
1. When the door is opening.
2. Pause of the automatic cooking.
3. When the cooking fan is working after cooking.
4. Demonstration mode
5. Child lock
6. Extend mode
7. Drain mode
8. Descaling mode
9. Kitchen timer mode
10. When the display shows “Err, WATER (flashing)”.
Grill heating element
Engine heating element
Intake damper motor
Tube pump motor
Fan motor
Antenna motor
Magnetron
Grill heating element
Engine heating element
Intake damper motor
Tube pump motor
Fan motor
Antenna motor
Magnetron
Grill heating element
Engine heating element
Intake damper motor
Tube pump motor
Fan motor
Antenna motor
Magnetron
Grill heating element
Engine heating element
Intake damper motor
Tube pump motor
Fan motor
Antenna motor
Magnetron
Grill heating element
Engine heating element
Intake damper motor
Tube pump motor
Fan motor
Antenna motor
Magnetron [duty]*10
Grill heating element
Engine heating element
Intake damper motor
Tube pump motor
Fan motor
Antenna motor
Magnetron [duty]*10
Start End Start End
Microwave Grill
Dual High
Grill(100%)/Micro(70%/50%/30%/10%)
Dual Low
Grill(50%)/Micro(70%/50%/30%/10%)
Steam High
Steam Low
*1
*1
*8
*7
*1
*8
*7
*2
*1
*8
*9
*2
*1
*2
*11
*3
*4
*6
*5
*1
*3
*4
*6
*5
15 min
10 min
1 min before "End"
1 min before "End"
30 sec. before end
30 sec. before end
*1 Fan motor will rotate for a while after cooking.
*2 Antenna motor will rotate only when high voltage transform-
er is energized.
*3 Grill heating element will be energized for 30 seconds be-
fore end of cooking.
*4 Engine heating element will be turned on and off by temper-
ature of thermistor (engine).
*5 Intake damper motor will rotate until a damper is closed
when cooking is started. And intake damper motor will ro-
tate until a damper is opened after the end of cooking.
*6 Tube pump motor will turned on and off by temperature of
thermistor (engine).
*7 Grill heating element will do the intermittent driving of 50% in ten
minutes.
*8 Intake damper motor will rotate until a damper is closed when
cooking is started. And intake damper motor will rotate until a
damper is opened after the end of cooking. Intake damper motor
will rotate for a short time at 3 minutes / 2 minutes / 1 minute be-
fore end of cooking.
*9 Grill heating element will do the intermittent driving of 50%.
*10 "duty" is intermittent driving.
*11 Magnetron will do the intermittent driving of 70% power level after
the magnetron is operated at 100% power level for 20 minutes.