background image

14

Child Lock

Allow you to use a PIN to protect certain settings from
being accidentally changed.

Setting the PIN

1

Press 

MENU

 and the MENU screen displays.

2

Press 

c

/

d

 to select “Setup”.

3

Press 

a

/

b

 to select “Child Lock”, and then press

OK

.

4

If you already set the PIN, enter it here.

5

Press 

a

/

b

 to select “Change PIN”, and then

press 

OK

.

New PIN

Reconfirm

Change PIN

Cancel PIN

6

Enter the 4-digit number as a PIN using 

0

 – 

9

.

7

Enter the same 4-digit number as in step 6 to
confirm.

• “The system PIN has been changed successfully”

displays.

NOTE

• To view a locked channel (Lock setting in Programme

Setup “Manual Adjust” is set to “On”), you must enter a
PIN. (See page 13.) When you select a locked channel, a
PIN prompt message pops up. Press 

OK

 to display the

PIN input window.

Cancelling the PIN

Allow you to reset your PIN.

1

Repeat steps 1 to 3 in 

Setting the PIN

.

2

Enter the PIN.

3

Press 

a

/

b

 to select “Cancel PIN”, and then press

OK

.

4

Press 

c

/

d

 to select “Yes”, and then press 

OK

.

NOTE

As a precautionary measure, make a note of your PIN
on the back of this operation manual, cut it out and
keep it in a safe place that children cannot reach. If
you lose or forget your PIN, initialise the TV to return
all settings except for the TV channel settings to factory
preset values. (See page 18.)

Menu operations

Position

For adjusting a picture’s horizontal and vertical
position.

1

Press 

MENU

 and the MENU screen displays.

2

Press 

c

/

d

 to select “Setup”.

3

Press 

a

/

b

 to select “Position”, and then press

OK

.

4

Press 

a

/

b

 to select “H-Pos.” or “V-Pos.”.

5

Press 

c

/

d

 to adjust the item to your desired

position.

WSS (Wide Screen Signalling)

Menu Operation: A (Page 9)

WSS allows a television to switch automatically among
the different screen formats.

NOTE

• Try to set WIDE MODE if an image does not switch to the

correct screen format. When the broadcast signal contains
no WSS information, the function will not work even if
enabled. (See page 16.)

NOTE

Adjustments are stored separately according to input
source.

H-Pos.:

 Centres the image by moving it to the left or right.

V-Pos.:

 Centres the image by moving it up or down.

Input Label

You can assign each input source a label you like.

1

Press 

b

 to select the desired input source.

2

Press 

MENU

 and the MENU screen displays.

3

Press 

c

/

d

 to select “Setup”.

4

Press 

a

/

b

 to select “Input Label”, and then press

OK

.

5

Press 

a

/

b

/

c

/

d

 to select each character of the

new name for the input source, and then press

OK

.

6

Repeat step 5 above until the name is fully spelt
out, and then press 

OK

.

• The name can be 6 characters or less.
• If a label name is less than 6 characters, select

“END”, then press 

OK

.

NOTE

• You cannot change the label if the input source is TV.

Item

LC-26P50E_GB_b

05.6.13, 8:00 AM

14

Содержание AQUOS LC-26P50E






















Отзывы: