OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Assembling Your Vacuum Cleaner
Using the Attachments
1.
Place vacuum in its upright position.
Make sure that the vacuum cleaner
is
NOT
plugged into the electrical
outlet when adding or removing
accessories.
2.
Turn the carpet adjustment knob
to the highest position
.
3.
Remove the hose connector from
the rear of the unit and push in the
desired attachment firmly onto the
end of the hose.
4.
If additional length is required,
attach one or both of the extension
tubes to the end of the hose and
then attach the crevice tool or
upholstery brush to the end of the
extension tube.
Motor Thermostat
Important
:
This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
•
Push the On/Off button once.
• Disconnect the plug from the
power source.
• Check the source of overheating
problem. (i.e. clogged hose or
filter)
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for
45 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1-800-798-7398.
Changing the Headlight Bulbs
1. Turn unit “Off” and unplug from wall
outlet.
2. With a Phillips #2 screw driver, remove
the two screws that are on the head
light lens. (Fig. 23)
3. Lift off the head light lens.
4. Remove the light bulbs by pulling them
out carefully.
5. Replace the new bulbs by pushing
them in.
6. Replace the head light lens and then
replace the two screws on the
head light lens to secure in place.
Fig. 23
Warning:
To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, HEPA filter,changing the filters or
performing maintenance/trouble shooting
checks.
14. Insert the right side of the agitator in
first by placing the end cap down
into the slot and then do the same
with the left side. Press firmly to
make sure that each end is
completely inserted.
15. Check to make sure that the belt is
centered on the pulley and that the
agitator turns.
16. Replace the top cover over the
power head base and replace the
screws, first the ones on the back
of the power head and then the
ones on the bottom and screw
firmly.
Note:
Do not plug the power cord
into an electrical outlet until
the vacuum is fully
assembled.
Handle Assembly
1. Carefully unpack all components,
set aside packaging.
2. Lift vacuum body to
upright position.
3. Remove the screws (2)
that come attached
to the body.
4. From the rear of
the vacuum, align
the handle with
groove and slide
onto vacuum. If
necessary, use
thumb and finger
pressure to slide
handle into position.
5. Once handle is in place,
secure the handle with
the screws (2). (Fig. 1)
Fig. 1
Warning:
Avoid tipping the vacuum or
setting it on furniture, fringed area rugs or
carpeted stairs while you are using the
hose with the attachments. When the
vacuum is turned on, the beater brush will
continue to rotate. Avoid leaving the
vacuum in one place for an extended
period of time, particularly on thick carpet.
Caution:
Do
NOT
pull the vacuum
cleaner around the room by the hose as it
could tip over and cause damage. When
using the attachments, do
NOT
over
extend the hose length when reaching.
Trying to reach beyond the hose reach
could cause the vacuum to tip over.
Caution:
Do not over tighten. Over
tightening could strip the screw holes.
Do not operate the vacuum without
the handle screws in place.
How to Start
The upright vacuum can be used on
multiple types of carpeting, bare floors or
upholstery with attachments. When using
the attachment tools such as the crevice
tool and the upholstery brush, place the
handle of the vacuum in the upright
position.
1. Turn the quick release cord holder
to either side 180° to release the
power cord.
2. Plug the power cord into the electrical
outlet.
3. Depress on the handle release pedal
to release the handle.
4. Push the On/Off button to the "On"
position to turn the vacuum on.
5. When using the attachments, the
vacuum must be in the upright
position. (Fig. 3)
Cord Assembly
1. Make sure that the quick release
cord holder is in the upright
position.
2. Remove the wire
tie from the
power cord.
3. Wrap the cord into
place by wrapping
it in a clockwise
direction around
the quick release
cord holder and
the lower cord
holder. (Fig. 2)
4. Turn the quick
release cord holder
to the left or to the
right to unwrap the power cord.
(Fig. 2)
Warning:
Do not plug in if the power
On/Off button is in the
"On" position.
Fig. 2
Fig. 3
9
4
Содержание UV219CS
Страница 2: ......
