OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
Cleaning the HEPA Dust Cup Filter
Changing & Cleaning the Pre-
Motor Filter
Warning:
To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, HEPA filter,changing the filters or
performing maintenance/trouble shooting
checks.
The pre-motor filter is located in the
vacuum underneath the dust cup.
Please note that this filter is a
washable filter and can be cleaned by
rinsing under lukewarm water. Always
allow the pre-motor filter to air dry for
24 hours before replacing in the
vacuum. Do not use a hair dryer to dry
it. Air dry only. To remove the pre-
motor filter:
1. Remove the front cover from the
vacuum cleaner. (Fig. 16)
2. Remove the dust cup (see
instructions on page 5 for removing
the dust cup).
3. Clean the pre-motor filter by rinsing
under lukewarm water.
4. After air drying for 24 hours, replace
in the vacuum.
Cleaning the Secondary Filter
1. Underneath the HEPA
filter there is a
secondary filter.
This is washable in
lukewarm water.
(Fig. 15) We
recommend washing
it when you are
washing your HEPA filter.
Always allow the secondary
filter to air dry for 24 hours
before replacing into the
vacuum. Never run
the vacuum without
the secondary filter in place.
Fig. 15
3. Remove the exhaust filter out.
(Fig. 17)
4. Rinse in lukewarm water and let
the filter air dry for 24 hours before
re-installing into the vacuum. Do not
use a washing machine to rinse the
filter. Do not use a hair dryer to dry
it. Air dry only. Never operate the
vacuum without
ALL
the filters in
place.
5. When the filter is dry, replace into
the vacuum and replace the front
cover.
Note:
A severely soiled or clogged
filter should be thoroughly washed with
fresh tepid water. A mild detergent can
be used if required.
Changing & Cleaning the Exhaust
Filter
Warning:
To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup, HEPA filter,changing the filters or
performing maintenance/trouble shooting
checks.
The exhaust filter is located on the
front of the unit below where the dust
cup is. To remove the exhaust filter,
you must first remove the front cover.
1. Check the exhaust filter frequently
and clean when dirty.
2. Remove the front cover. (See
instructions on page 5.)
Fig. 17
Cleaning the HEPA Filter Frame
1. Before replacing the HEPA filter in the
HEPA Filter frame, you can (should)
rinse the frame in lukewarm water by
just running it under the tap to remove
any dust that is adhering to the frame.
(Fig. 13) Do
NOT
place in dishwasher.
Fig. 13
2. Make sure that the filter frame is
completely dry before replacing into
the dust cup.
Fig. 9
1. To remove the HEPA
filter, unlock and remove
the dust cup container
cover by turning the cover
to the right until the
arrow on the cover
aligns with the arrow
on the handle and then
lifting the cover off.
2. Remove the HEPA
Rinseable "Tap Clean"
filter from the dust cup. (Fig. 9)
Fig. 11
3. Remove the filter ring that is
around the HEPA filter. Vigorously
"TapClean"
the HEPA dust
cup filter on a
hard surface until
no more dust is
observed falling
out. (Fig. 10)
Please note
that there is a
filter brush
included with
your vacuum. It is located
underneath the dust
cup cover. You can
use the brush to clean
the pleats of the HEPA
filter. (Fig. 11)
Alternatively, the
HEPA filter may also
be washed by running
it under the tap allowing
the water to run on the
dirty side. (Fig. 12) We
recommend washing it
once a month or when suction
Fig. 12
IMPORTANT, Please Note:
The Rinseable
“TapClean” HEPA Dust Cup Filter will stop
most of the tiniest dust particles and
airborne allergens from re-entering the air
you breathe. In fact it stops 99.97% of all
particles as small as 0.3 microns - many
times smaller than a human hair!!! Because
of this incredible filtration performance, the
HEPA Dust Cup Filter will quickly
accumulate many fine dust particles inside
the white filter folds that are difficult to see
but which will eventually block or reduce
your suction power - if not cleaned properly.
Clean the HEPA Filter after each use as
described in this section.
Cleaning the Filter Ring
1. Around the HEPA filter
there is a filter ring.
This is washable in
lukewarm water.
(Fig. 14) To remove
the filter ring, slide it
off the HEPA filter.
2. We recommend
washing the filter ring
when you are
washing your HEPA
filter. Always allow the
filter ring to air dry for
24 hours before replacing onto
the HEPA filter. Never run the vacuum
without all the filters in place.
Note:
This is a washable filter, but we
recommend replacing it every three (3)
months.
Fig. 14
Fig. 10
Please Note
: The white material in the
HEPA filter will discolor over time - This is
NORMAL and will NOT affect the
performance of the filter.
Warning
: Always empty the dust cup
and clean the HEPA dust cup filter
before each use and during prolonged
usage. Never over fill the dust cup -
remove dirt and clean the HEPA dust
cup filter each time the dust cup is
emptied during prolonged usage or risk
motor damage.
appears reduced. Always allow 24
hours for drying before replacing
into the vacuum.
6
Fig. 16
7
Содержание UV219CS
Страница 2: ......
