13
14
AUST: 1800 890 840
NZ: 0800 002 999
IMPORTANT:
Do not use on unsealed wood or unglazed
ceramic floors. Do not use on wood or tile floors that
are highly worn, unfinished or have a wax or oil finish.
Surfaces that have been treated with wax or some
no wax floors may be damaged by the cleaning and
polishing solutions therefore it is always recommended
to test an isolated area of the surface to be cleaned or
polished before proceeding. You should check the use
and care instructions from the floor manufacturer before
cleaning or polishing.
IMPORTANT:
Do not use more than one brand of floor
polish to polish one room. Use only Shark
®
Wood & Hard
Floor Polish.
6
Use the Sonic Duo
™
to spread the polish evenly
over the floor. Do not go over an applied area too
frequently. Always leave an area looking wet. If a
section begins to look dry while polishing, add more
Wood & Hard Floor Polish to the area. Repeat until
the whole area has been polished.
7
When going from section to section, do not lift the
Sonic Duo
™
to move it, always slide it to the next
section. No rinsing is required.
8
Allow the Wood & Hard Floor Polish to dry for at
least 1 hour in light traffic areas and a complete 24
hours for the polish to cure before returning to heavy
traffic areas.
9
When finished, turn the unit off and slide and lift the
Sonic Duo
™
to remove it from the area that was just
polished. Lay the Sonic Duo
™
on its side and remove
the Hard Floor Polishing Pad by hand.
(Fig. 33)
NOTE
: Depending on the amount of traffic your
floors sustain, Shark
®
recommends polishing every
2 months. Touch up high traffic areas as needed
in-between full floor polishes.
Polishing Your Hard Floors:
1
Vacuum the floor to remove all loose dirt, dust
and grit from the floor surface. For best results,
we recommend that you clean the floor using the
Shark
®
Wood & Hard Floor Cleaner first and allow
time to dry before polishing.
2
Attach the Hard Floor Polishing Pad to the bottom of
the Sonic Duo
™
. This pad has a “Orange” trim and
the “Orange” tag says “Hard Floor Polishing Pad”.
(Fig. 30)
3
Lightly step on the back of the scrubbing head to
release the handle.
WARNING: Never stand on the Sonic Duo
™
.
4
Carefully, squirt a liberal amount of the Floor Polish
onto an area of the floor to be polished and place the
polishing pad over it before you start the unit. Make
sure that the polishing pad is saturated and then
squirt the polish in 12x12cm sections.
(Fig. 31)
5
Turn the On/Off button to “On (I Low)” setting.
Always squirt the floor polish from a height of 15cm
above the floor to avoid splashing the polish over the
floor. One bottle is enough to cover 40m
2
.
(Fig. 32)
NOTE:
The 500ml polish bottle is enough to cover
24m
2
.
IMPORTANT: NEVER
add the Sonic Activated Wood & Hard Floor Polish
to the Reusable Bottle or run it through the Sonic Duo
™
unit.
Frequently Asked Questions
Q.
Polishing has left my floors streaky or spotty.
A.
You should go over the streaky or spotty area with
more polish. Always leave the area looking very
wet, never dry.
Q.
There is a footprint, smudge or uneven spot after or
during polishing.
A.
You should add more polish to any problem areas
during polishing. Always leave the area looking
very wet, never dry.
Q.
I accidentally ran the Shark
®
Wood & Hard Floor Polish
through the Sonic Duo
™
and now it is not working
properly.
A.
Shark
®
Wood & Hard Floor Polish should always
be squirted directly onto the floor . If it was
run through the unit, you need to flush it out
immediately. Fill the Reusable Bottle with warm
water and spray it through the system to flush
it. Then turn and remove the tip of the nozzle to
clean it.
(Fig. 34)
Using Your Sonic Duo
™
Carpet, Wood & Hard Floor Cleaner - cont.
fig. 30
fig. 31
fig. 32
fig. 33
fig. 34
