9
10
AUST: 1800 890 840
NZ: 0800 002 999
10
Using the same back and forth motion, continue to
go over the same area without spray. For heavily
soilied high traffic areas or dingier carpets you
may need to go over the area for several minutes,
spraying periodically. Spray more solution as needed
while cleaning. Repeat as necessary until the entire
carpeted area has been cleaned. No rinsing is
required.
11
If the Reusable Bottle is empty, you can refill it at any
time as long as the Sonic Duo
™
is unplugged from
the outlet.
12
Once finished, step on the tag of the Carpet Scrub‘n
Stain
™
Padand lift the unit to remove the Carpet
Scrub‘n Stain
™
Pad from the Sonic Duo
™
(Fig. 21)
.
Let the carpet dry thoroughly and then vacuum.
SPOT & STAIN CLEANING
Please note that not all carpets react to the Sonic Duo
™
the same way. Some carpets will require more time and
cleaning solution than others.
Step 1:
1
Vacuum the stained or discoloured area to remove
any loose dirt, dust, or debris that may have
accumulated in your carpet.
Step 2:
2
Begin by pretreating the stain with the Activating
Pretreater Carpet Stain & Odour Remover until the
stain or discolouration is fully saturated.
3
Let sit for 5-10 minutes.
4
Use a white cloth with a blunt object to blot up the
stain.
5
You will see the stain begin to transfer from the
carpet onto the white cloth.
6
Continue to use fresh areas of the white cloth as you
blot up more and more of the stain.
7
Never rub.
8
Repeat as necessary.
6
Screw the bottle cap on tightly and insert the
Reusable Bottle into the unit. Push it down to
make sure that it is well inserted. You will hear an
audible “Click” when the Reusable Bottle is inserted
properly.
(Fig. 17)
7
Twist the quick cord release holder to unwrap
the power cord completely.
(Fig 18)
Plug into an
electrical outlet and slide the “ON/OFF” button to
turn the Sonic Duo
™
on. Select the faster Carpet
Mode (II).
(Fig 19)
8
Lightly step on the back of the scrubbing head to
release the handle.
WARNING: Never stand on the Sonic Duo
™
.
9
Begin cleaning by pressing the Spray Button to
apply the cleaning solution to the carpet that is to be
cleaned.
(Fig. 20)
Spray the solution continuously
while pushing the unit forward and then pulling it
backward several times until the area to be cleaned
is damp.
NOTE:
The first time that you use the Sonic Duo
™
there may be air in the system causing a delay for
the solution to come out of the spray nozzle. Hold the
spray button down for 5 to 10 seconds until you see
the solution spray out.
Frequently Asked Questions
Q.
I noticed a rippling effect on the edges of my area rugs
– should I be concerned?
A.
Wool are rugs sometimes have a rippling effect on
the edges after cleaning. This rippling will relax
our after a few days of regular wear and usage.
Q.
After using the Low Moisture –No Rinse- Carpet
Cleaner, my carpet feels dry and crunchy – what can
I do?
A.
If your carpets feel crunchy, you likely used too
much of the Low Moisture – No Rinse- Carpet
Cleaner. The dry crunchy feeling will go away after
a few days of normal wear and usage. Another pass
vacuuming should also help break up the crunchy
texture more quickly. To avoid this from happening
again, we recommend using less solution on one
specific area or a less concentrated dilution.
Q.
How can I remove tough stains?
A.
Begin by treating the stain with the Activating
Pretreater until fully saturated. Let sit for 5-10
minutes. Next, use a white cloth with a blunt object
to blot up the stain. You will see the stain transfer
from the carpet onto the white cloth. Continue
to use fresh areas of the cloth as you blot up
more and more of the stain. Never rub. Repeat as
necessary.
fig. 17
fig. 18
fig. 19
fig. 20
fig. 21
Using Your Sonic Duo
™
Carpet, Wood & Hard Floor Cleaner - cont.
