Shakmat Harlequin's Context Скачать руководство пользователя страница 20

Страница: 20 / 21

www.shakmat.com

•

18/19

13. Debug

The module does not turn on

Check the orientation of the Tactical plan.

Re-check the electrolytic capacitors and power cable orientation.

The module is stuck in the calibration routine, or one or several outputs

are not working

Check the jack connectors & Tactical plan soldering.

One or several LEDs are not working

Check the LEDs solder points and LED orientation.

Check the Tactical Plan headers solder points.

For the amber LEDs, check the PCB to PCB headers solder points on both

PCBs.

One or several potentiometers are not working

Check the solder points and Tactical Plan headers solder points

One or several buttons are not working

Check the buttons solder points.

Check the PCB to PCB headers solder points on both PCBs.

The 7 segment display is not working

Check the display solder points.

Check the PCB to PCB headers solder points on both PCBs.

Содержание Harlequin's Context






















Результаты поиска

Содержание Harlequin's Context

Отзывы:

Похожие инструкции для Harlequin's Context

Бренды по названию

Популярные бренды

Shakmat Harlequin's Context, Руководство по эксплуатации

Результаты поиска

Содержание Harlequin's Context

Отзывы:

Похожие инструкции для Harlequin's Context

Бренды по названию

Популярные бренды