SGS MD-1200-1 Скачать руководство пользователя страница 15

5. LIGHTING CONTROL KEY AND LED

: LED lights when pressed, allows the lamp relay 

output. LED turns off when the button is pressed again, it does not relay outputs.

HIDDEN FUNCTIONS:
 

The device is available in 6 hidden function parameter setting. These parameters are set as follows. 
Hidden function parameters from 

Pr1 and Pr.2 only works when Turbo function active.

 

Pr.1: When the Start button is pressed, the SET temperature turbo will enter standby to work out the 
difference (between 10ºC to 90ºC setting)
Pr.2: waiting time at turbo operation (setting from 1 min to 9 minutes)
Pr.3: Upper hysteresis setting (between -9ºC setting with + 9ºC)
PR.4: lower hysteresis setting (between 0ºC and 9ºC setting)
Pr.5 after setting there will be a few degrees of cooling fan (between 30ºC and 100ºC setting)
Pr.6: Buzzer passivation (0 or 1 adjustable) 

    USING THE DEVICE

6.  TURBO  BUTTON  AND  LED: 

Key  LED  lights  up  when  the  key  is  pressed,  all  the 

resistance  is  started  full  operation  is  activated.  Resistance  indicator  of  "10"  since  the 
author  and  LEDs.  key  LED  turns  off  when  the  key  is  pressed  again.  The  preset 
resistance levels are seen in the display and the oven will continue to work according to 
the  proportional  value.  When  the  Start  button  is  pressed,  the  turbo  is  activated 
automatically. turbo is automatically deactivated when the setpoint is reached.

7. START / STOP KEY AND LED: 

LEDs light when pressed and switches to position 

START. Depending on the appliance starts to control temperature setpoint.
Turbo automatically activated when the measured temperature is below the set value, 
resistors full works. setpoints are changed when the start position. According to the new 
setpoint temperature control set will continue to run. Measured temperature setpoint 
temperature until it reaches the relay is resistance remains and the temperature is set LED 
burns. Measuring the resistance value reaches the set value
relay releases, the set temperature LED is off. Stop key to switch the device to position 
printed and LED turns off all the controls and relays are disabled. device faults
All controls and switches to stop position will be canceled.

8. ON-OFF KEY AND LEDS:

 LED lights red button when the device is energized. the 

device is energized when the key is pressed. Key LED lights and green lights all the 
indicators. Pressing the button again deleted and key indicators are lit red.

9. STEAM ON-OF KEY AND LED: 

When the Steam On-Off key is pressed, the steam 

thermostat  enters  the  circuit. As  long  as  the  thermostat  is  active,  the  On-Off  button 
flashes. When the thermostat is deactivated, the device signals swich input. The On-
Off button remains lit continuously.

10. STEAM BUTTON AND LED: 

Steam is ready. The steam valve exits as long as 

the  steam  key  is  held  down.  Otherwise  the  key  will  not  sound  and  will  sound  an 
alarm. In case of failure, the control will be canceled.

15

Содержание MD-1200-1




























Отзывы: