background image

7

Unpacking

Unpack the device and inspect it to ensure that it has not been damaged during transport.
The G-1 Beam (POI) is shipped with:

• 

1 x TRUE1 power input connector, 2 m /78 in. (standard only). In POI versions, it is supplied a power cable with bare ends.

• 

1 x Omega brackets with 1/4-turn fasteners (standard only).

• 

Base with 3 x batteries (optional - standard only).

• 

2 x M-10 screws (POI Only).

• 

Safety information leaflet.

Location / application

The standard fixture is IP65-rated and is designed for both indoor and outdoor events. This means that it is protected from:

• 

Dust, to the degree that dust cannot enter the fixture in sufficient quantities as to interfere with its operation.

• 

Lower pressure jets of water from any direction. 

The POI fixture is IP66-rated and designed for use in outdoor installations. This means that it is protected from:

• 

Dust, to the degree that dust cannot enter the device in sufficient quantities as to interfere with its operation.

• 

High pressure water jets of water from any direction. 

When selecting a location for the device, ensure that:

• 

It is situated away from public thoroughfares and protected from contact with people.

• 

It has adequate ventilation.

•  It is not immersed in water. 

When using standard fixtures outdoors or in wet locations, ensure that:

•  For wireless DMX or standalone operation,

 the DMX out cable is properly attached to the DMX-in connection.

•  For cabled DMX operation,

 the DMX out of the last fixture is terminated with a 120 Ohm resistor between pin 2 and 3    

(according to the RS485 standard), or properly sealed, in accordance with the ingress protection (IP) requirements. 

Transportation

Always use the supplied packaging or suitable flight case for transportation and storage.

Never carry the fixture by connected cables or wires; use the handles. 

Locating the front of the G-1 Beam (POI)

•  With the G1 Beam head

: the front of the fixture is the opposite side of the AC power input socket. 

•  Without the G-1 Beam head:

 the base it is marked with an arrow, as shown in the illustration below (POI n/a).

Preparing for installation

Figure 2: Locating the front of the G-1 Beam

Содержание G-1 BEAM

































Отзывы: