manualshive.com logo in svg

SEW-Eurodrive MOVI-PLC basic DHP11B-T0, Руководство пользователя

Поделиться
Скачать
SEW-Eurodrive MOVI-PLC basic DHP11B-T0 Скачать руководство пользователя страница 57

5

PROFIBUS-DP Operating Characteristics

Special cases

Manual – MOVI-PLC

®

 basic DHP11B.. controller

57

Incorrect service 
code in the 
parameter channel 

Incorrect code was specified in the management byte or reserved byte during parameter
setting via the parameter channel. The following table shows the return code for this
special case.

Troubleshooting:

Check bits 0 and 1 in the parameter channel.

Incorrect length 
specification in 
parameter channel 

A data length other than 4 data bytes was specified in a 

read 

or 

write 

service during

parameter setting via the parameter channel. The following table displays the return
codes.

Troubleshooting:

Check bit 4 and bit 5 for the data length in management byte 0 of the parameter channel.
Both bits must be set to "1".

Internal 
communication 
error

The return code listed in the following table is sent back if an internal communication
error has occurred. The parameter service transferred via the fieldbus may not have
been performed and should be repeated. If this error persists, switch the MOVI-PLC

®

basic 

DHP11B.. controller off and on again. In this way, the control card is reinitialized.

Troubleshooting:

Repeat the 

read 

or 

write 

service. If the error occurs again, briefly disconnect the MOVI-

PLC

®

 

basic 

DHP11B.. controller from the power supply and switch the system on again.

If the error persists, consult the SEW Electronics Service.

Code (dec)

Meaning

Error class:

5

Service

Error code:

5

Illegal parameter

Add. code high:

0

–

Add. code low:

0

–

Code (dec)

Meaning

Error class:

6

Access

Error code:

8

Type conflict

Add. code high:

0

–

Add. code low:

0

–

Code (dec)

Meaning

Error class:

6

Access

Error code:

2

Hardware fault

Add. code high:

0

–

Add. code low:

0

–

0

0

I

Содержание MOVI-PLC basic DHP11B-T0

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды