SEW-Eurodrive MOVI-PLC basic DHP11B-T0 Скачать руководство пользователя страница 26

Страница: 26 / 96

Assembly / Installation Instructions

Installation of MOVI-PLC® basic DHP11B.. controller in MOVIDRIVE®

Manual – MOVI-PLC

basic DHP11B.. controller

3.6

Installation of MOVI-PLC

basic DHP11B.. controller in MOVIDRIVE

MDX61B

3.7

Installation of MOVI-PLC

basic DHP11B.. in the MOVIAXIS

master module

3.7.1

Functional description of the terminals, X5a / X5b (MOVIAXIS

master module)

• The connectors X5a and X5b are connected in parallel. In this way, the voltage

supply of the MOVIAXIS

master module can be provided from the right to X5b or

from below to X5a. With connection to X5a, further modules can be connected via
X5b (e.g. supply module, axis module). The voltage supply of brake (X5a/b:3, 4) is
conducted by the MOVIAXIS

master module.

• The MOVI-PLC

basic

DHP11B.. controller can be supplied by the MOVIAXIS

switched-mode power supply module (MXS) or from an external voltage supply. For
this purpose, connect X5 between the individual devices.

• If the MOVI-PLC

basic

DHP11B.. controller is supplied with DC 24 V by the

MOVIAXIS

switched-mode power supply module, the function of the MOVI-PLC

basic

DHP11B.. controller is maintained after disconnection from the power supply.

This requires an external DC 24 V supply of the MOVIAXIS

switched-mode power

supply module.

MOVI-PLC

basic

DHP11B.. controller is installed as stipulated in section 3.4. The

MOVI-PLC

basic

DHP11B.. controller is supplied with voltage by MOVIDRIVE

MDX61B. A separate voltage supply is only required for the digital inputs and outputs
(connector X31).

MOVI-PLC

basic

DHP11B.. controller is installed as stipulated in section 3.4. To wire

the system bus, connect connector X33 (CAN1) or X32 (CAN2) of the MOVI-PLC

basic

DHP11B.. with connector X9 (MOVIAXIS

supply module signalizing bus or of a

MOVIAXIS

axis module) or with connector X12 (CAN2 bus of a MOVIAXIS

axis

module). The MOVIAXIS

master module also provides further connections as

described below.

MOVIAXIS

master

module MXM

Designation

Terminal

Function

59233AXX

Connector X5b

X5b:1
X5b:2

X5b:3
X5b:4

DC 24 V

DGND

DC 24 V

BGND

Voltage supply for control electronics
Reference potential of control elec-
tronics
Brake voltage supply
Reference potential for brake connec-
tion

Connector X5a X5a:1

X5a:2

X5a:3
X5a:4

DC 24 V

DGND

DC 24 V

BGND

Voltage supply for control electronics
Reference potential of control elec-
tronics
Brake voltage supply
Reference potential for brake connec-
tion

X5b

3
4

X5a

Содержание MOVI-PLC basic DHP11B-T0

































































































Результаты поиска

Содержание MOVI-PLC basic DHP11B-T0

Отзывы:

Бренды по названию

Популярные бренды

SEW-Eurodrive MOVI-PLC basic DHP11B-T0, Руководство пользователя

Результаты поиска

Содержание MOVI-PLC basic DHP11B-T0

Отзывы:

Бренды по названию

Популярные бренды