19
SESAMO
PROSWING
During parameters setting any movement of motor is allowed.
When parameters setting it is not used, push button [ENT] is an opening command (only with
One Radar or Two Radars logics).
START UP
1.
Set main power switch (Fig.1 A) on OFF.
Make sure to have properly adjusted DIP-Switches, in particular 1 and 5. Make sure
contacts KEY, SAFE CLOSE e SAFE OPEN are properly connected or, if not used, connected
to COM.
2.
Give power supply to the automatism switching on 230 V the general switchboard.
3.
Set the switch (Fig.1 A) in ON.
4.
Verify lighting of the display and if it shows E6 (if necessary set the jumper to light
properly the display (look at Fig.27);
5.
Select LS with push buttons [+] e [-], push [ENT] when it shows [--] push again
[ENT] for 5 seconds to confirm, when disappears [--] release push button [ENT], the
procedure of the acquisition of the monitoring sensors will start (refers to
paragraph “sensors installation” page 13/14 to finalize the procedure)
6.
If present an electric lock, set parameters 10/11/12/14 (look paragraphs
“parameters
adjustment-
display” and/or “electric locks setting”).
7.
Pushing buttons [+] e [-], select LP and push [ENT], when it shows [--] push again
[ENT] for 5 seconds to confirm the commend; when disappears [--] release push
button [ENT]. Door opens and it will start a cycle of parameters acquisition.
ATTENTION: While opening of the door, stop the wing in the position fixed as limit
in opening, to get the maximum opening angle. Immediately after this operation, the
door will close fully and on display CL blinks. When the door reaches the completely
closed position, and CL do not blink any more, it will be possible to test the operation of
the automatism pushing the button [ENT]: the door opens and closes normally. The
opening angle, during normal operation, will be reduced compared to the limit detected
during the acquisition of the limits so to allow the operation even if the mechanic door
limit is missing. The percentage of reduction is defined by parameter n.33. At each start
(or RESET operation), automatism must reach the position of door fully closed. Later the
first cycle will be at reduced speed.
MESSAGE OR ERRORS CODE
Display are also used to show message or error code:
SEGNALAZIONE
DESCRIZIONE
OP Fixed
Door opened
OP Blinking
Door opening
Содержание PROSWING R
