background image

 

2

 

DMR Repeater SBR8000, SCR8000, SER8000 

Safety 

Read these safety instructions carefully. 

Attention! 

Sepura products are intended for use in occupational/controlled 
conditions. 

It is the responsibility of the person operating the product to 
ensure that it is operated safely at all times, and that local laws 
and regulations governing the usage of Radio Frequency (RF) 
products are observed. Obey all signs and instructions relating 
to the usage to RF wireless devices. 

It is recommended that you obtain training on how to safely 
operate this product. Your personal safety could be affected if 
you do not understand how to operate this product correctly.  

This product must not be operated in environments that exceed 
those listed in the product technical datasheet and in the 
Regulatory section of the product user guide.  

Unauthorised modifications to the product could cause the 
product to become non-operational. Always use Sepura 
approved antenna, battery and accessories with this product. 

Exposure to RF energy 

Sepura designs and manufactures products to meet strict 
guidelines and international standards relating to Radio 
Frequency (RF) energy and the potential health risks associated 
with using such products. If you have any concerns about 
potential health risks associated with long term exposure to RF 
energy, you should obtain advice from your employer. 

RF energy interference with electronic equipment 

Some personal medical devices, such as hearing aids and 
pacemakers, can be affected by RF energy. Always consult your 
service provider or the manufacturer of the medical device 
before using RF wireless devices. 

Important safety notes about the Antenna 

NEVER touch the antenna when the repeater is transmitting, 
this may cause a minor burn to the skin and may affect the 
operational range of the antenna.  

NEVER use your repeater without an antenna attached. 
Transmitting without an antenna may damage the product. 
Only use a Sepura approved antenna with your repeater. 

The antenna must be installed and operated with a minimum 
distance of 1.2m to any person. This distance has been calculated 
based on a 2dB cable loss between radio and antenna. 

Accessories 

Sepura products have been tested to meet strict guidelines for 
personal safety and operational conditions. Only accessories 
approved by Sepura are recommended for use with this 
product. Always read the instructions supplied with the 
accessory for additional safety instructions.  

The use of non-approved accessories may invalidate any 
product warranty. If a non-approved accessory is fitted, it may 
compromise the product safety ratings.  

Safe installation 

CAUTION!

 This product has double pole/neutral fusing.  

Содержание SBR8000
















Отзывы: