manualshive.com logo in svg

Sentex SW470, Инструкция по установке и обслуживанию

Поделиться
Скачать
Sentex SW470 Скачать руководство пользователя страница 30

30

  

Warranty Policy 

 

Doc 01-G0665 
Rev A 

Warranty Policy 

Seller warrants that the goods are free from defect in materials and/or workmanship for 
a period of one year from the date of shipment from the F.O.B. point. Goods returned to 
Seller for warranty repair within the warranty period, which upon receipt by Seller are 
confirmed to be defective and covered by this limited warranty, will be repaired or 
replaced (at Seller’s sole option) at no cost and returned pre-paid. Defective parts will 
be repaired or replaced with new or factory-rebuilt parts at Seller’s sole option. 
Authorization instructions for the return of any goods must be obtained by Buyer from 
Seller before returning the goods. The goods must be returned with complete 
identification, freight prepaid, and in accordance with Seller’s instructions or they will not 
be accepted. In no event will Seller be responsible for goods returned without proper 
authorization or identification. 
 
THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS 
OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR 
FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE, AND OF ANY OTHER 
OBLIGATIONS OR LIABILITY ON SELLER’S PART. THIS LIMITED WARRANTY 
DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY IMPROPER 
INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO 
ABUSE, MISUSE, FAILURE TO PROVIDE REASONABLE AND NECESSARY 
MAINTENANCE, OR ANY ALTERATIONS TO THIS PRODUCT), LABOR CHARGES 
FOR DISMANTLING OR REINSTALLING A REPAIRED OR REPLACED UNIT, OR 
REPLACEMENT BATTERIES. UNDER NO CIRCUMSTANCES SHALL SELLER BE 
LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN 
CONNECTION WITH THE USE, OR INABILITY TO USE, THIS PRODUCT.  IN NO 
EVENT SHALL SELLER’S LIABILITY FOR BREACH OF WARRANTY, BREACH OF 
CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE 
PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR 
US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT. 
Some states do not allow the exclusion or limitation of consequential, incidental or 
special damages, so the above limitation or exclusion may not apply to you. This limited 
warranty gives you specific legal rights, and you may also have other rights which vary 
from state to state. 
 

 
 
 
 

Содержание SW470
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды