Sentex SW470 страница 16 Скачать руководство пользователя | Manualshive

Страница: 16 / 31

background image

16

Installation

Doc 01-G0665
Rev A

Figure 11

Gate Bracket Installation

1

If required, install an angle (2” x 2” x ¼” by others) horizontally on the gate, at
the same height as the top surface of the control arm extension.

01-G0665F6

Figure 12

2

Adjust the eccentric stop as shown so that the wide area of the eccentric is
against the arm. Be sure that the control arm and actuator are in a straight line.
Install the gate bracket at the appropriate point on the gate (or angle, if used).

As an alternative on the Model SW470 only, (2) 3/8 – 16 bolts and a nut plate
are provided. Adjust arm length and then rotate the eccentric stop 180 degrees
so that the small thickness is against the arm. This will provide the necessary
deflection in the arm assembly to lock the gate.

01-G0665F8

Figure 13

«
...
14
15
16
17
18
...
»

Содержание SW470
































Отзывы:

Нет отзывов

Похожие инструкции для SW470

Power Drive Security+ HD200CD

Бренд: Chamberlain Страницы: 80

Power Drive Security+ PD210CS

Бренд: Chamberlain Страницы: 80

Бренд: SOMFY Страницы: 60

Бренд: SOMFY Страницы: 80

Бренд: Parkside Страницы: 16

Бренд: CAME Страницы: 16

76380 - Classic Chrome Heavyweight Can...

Бренд: Hamilton Beach Страницы: 5

Бренд: Fabet Страницы: 28

SensingEdge MT22

Бренд: Miller Edge Страницы: 2

Бренд: Chamberlain Страницы: 36

Бренд: SEA Страницы: 12

Бренд: SEA Страницы: 14

Бренд: E.T. Страницы: 8

Бренд: Dea Страницы: 58

Бренд: FAAC Страницы: 23

AccessMaster Security+ M3100M-1/2HP

Бренд: Chamberlain Страницы: 36

Бренд: CAME Страницы: 84

Бренд: CAME Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды