Sentex SW470 Скачать руководство пользователя | Manualshive

Страница: 12 / 31

background image

12

Installation

Doc 01-G0665
Rev A

Installation

In order for the gate operator to function correctly it is important that the gate be level
and swing smoothly and freely. If it does not, damage to the operator may result and
the life expectancy will be greatly reduced.

SW470 gate operators have provisions for both post and pad mounting. However,
because of the high torque involved in most swing gate installations, pad mounting is
the recommended method.

NOTE:

Instructions are for right hand operator installation. Left hand is opposite.

01-G0665F1

Figure 4

Post Mount for SW470 Operator Only

1

Locate mounting post and electrical conduit locations. The operator cabinet
may be installed either parallel or perpendicular to the fence.

2

Excavate required areas for conduit installation and mounting posts.

3

Set mounting post and electrical conduit in place. Knockouts for 3” pipe clamps
(not supplied) are provided in the operator.

NOTE:

Distance between mounting posts and the relative location to gate

is very important.

4

Pour cement to secure mounting posts and allow to set for two days before
installing power unit.

01-G0665F16

Figure 5

«
...
10
11
12
13
14
...
»

Содержание SW470
































Отзывы:

Нет отзывов

Похожие инструкции для SW470

Бренд: FAAC Страницы: 32

Бренд: DTS Страницы: 19

Бренд: Control-A-Door Страницы: 32

Бренд: iSmarGate Страницы: 29

Бренд: Becker Страницы: 16

SensingEdge MT22

Бренд: Miller Edge Страницы: 2

Controll-A-Door R

Бренд: B&D Страницы: 28

Бренд: B&D Страницы: 32

Бренд: GSM Activate Страницы: 6

Бренд: Fagor Страницы: 22

Бренд: Beninca Страницы: 40

Бренд: Zero Страницы: 12

Бренд: Raynor Страницы: 28

Бренд: Kenwood Страницы: 94

Бренд: JCM Страницы: 6

Бренд: Beninca Страницы: 4

Бренд: Merlin Страницы: 32

commander myq MT110MYQ

Бренд: Merlin Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды