Sentex SW470 страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 31

background image

18

Installation

Doc 01-G0665
Rev A

Electrical Power Connections

CAUTION

Make sure power is disconnected at the main power source and at the
operator’s electrical disconnect switch before proceeding.

Secure all electrical power connections inside the power wiring compartment. Use the
electrical wiring diagram supplied with this unit.

All single phase operators will have – L1 (neutral), L2 (hot) and ground. All three phase
operators will have – L1, L2, L3 and ground. It is very important that operator is
properly grounded.

IMPORTANT NOTE:

On three phase operators the power connections must be

properly phased. If they are phased wrong the gate operator will run
backwards. To correct this situation, disconnect power a main power source
and at the operator’s electrical disconnect switch. Then, reverse any two of the
three power leads.

01-0665F10

Figure 15

«
...
16
17
18
19
20
...
»

Содержание SW470
































Отзывы:

Нет отзывов

Похожие инструкции для SW470

Бренд: Chamberlain Страницы: 28

Бренд: Chamberlain Страницы: 2

ZEROQUATTRO 180

Бренд: O&O Страницы: 2

Бренд: UNAC Страницы: 24

Бренд: Wisniowski Страницы: 76

Бренд: Xtreme Garage Страницы: 28

Бренд: CAME Страницы: 16

Бренд: FAAC Страницы: 44

Бренд: GDS Страницы: 11

Бренд: tau Страницы: 40

Бренд: Ghost Controls Страницы: 64

Бренд: Ghost Controls Страницы: 68

Бренд: FAAC Страницы: 16

Бренд: Toastmaster Страницы: 9

Бренд: Chamberlain Страницы: 72

Бренд: Chamberlain Страницы: 88

Бренд: Chamberlain Страницы: 14

Бренд: Dea Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды