Sensa Core ST-200 aQua Скачать руководство пользователя страница 84

Страница: 84 / 92

ST-200 aQua

Operator’s Manual

Note:

Make sure that the flow cell cover should be kept on the top of the

flow cell/bubble detector if the analyzer is kept in ideal state to protect

from the dust.

Figure 20

Figure 21

F. Printer

If the ST-200 aQua printer fails to print, attempt the following

procedures:

1. To verify that the printer is turned on, enter the SETUP MENU and

check PRINTER ON/OFF.

2. Check the printer mechanism for any paper obstructions in the

printer head area. Remove any obstructions if possible, without

damaging the printer assembly or paper tear bar.

3. If steps 1 and 2 are successful, but the printer remains inactive,

remove the analyzer power cord for ten seconds, and then reinstall

the power cord. Press the paper advance button. The printer head

should move across the paper and the paper should advance

forward.

If the printer continues to function abnormally, contact your

ST-200 aQua distributor.

Performance Verification

Periodically, the laboratory may want to verify the analyzer’s performance.

ST-200 recommends the following procedures:

CALIBRATION – Automated

1 Press “Y” to SYSTEM NOT CALIBRATED PLEASE CALIBRATE.

2 Calibrant B and Calibrant A from the solutions pack are aspirated

and measured internally.

3 ANALYZE SAMPLE indicates a successful calibration. If an error is

displayed, refer to instructions in the troubleshooting section.

Содержание ST-200 aQua





























































































Результаты поиска

Содержание ST-200 aQua

Отзывы:

Бренды по названию

Популярные бренды

Sensa Core ST-200 aQua, Руководство оператора

Результаты поиска

Содержание ST-200 aQua

Отзывы:

Бренды по названию

Популярные бренды