Sensa Core ST-200 aQua Скачать руководство пользователя страница 12

Страница: 12 / 92

ST-200 aQua

Operator’s Manual

Figure 6

Loading the Stack

Slide the electrode stack into the electrode housing. Push down firmly

until the bubble detector snaps into position.

Carefully install the bubble detector and the electrode blocks into the

electrode housing in such a manner that electrode blocks silver pins

should be inserted in female connector.

Do not force the electrode housing into place. If the electrode blocks are

properly installed, the electrode housing should slide easily into position.

d. Installation of tubing:

The ST-200 aQua Electrolyte analyzers comes with two pump motors.

The first pump motor is used for the flow of CAL-A & CAL-B solutions in to

the electrode housing in control with the valve. Its inflow is from the valve

and outflow is to the bubble detector flow cell and electrode housing.

Connect its outflow tube at the side of the flow cell pin.

The second pump motor is used for the flow of sample, QC, CAL-A & CAL-

B fluids from electrode housing to the waste bottle. Its inflow is from

electrode housing and outflow is to the waste bottle. Its pump tube has

two stoppers. One stopper (red) is connected at the base of the electrode

housing and the other stopper (blue) is connected to the waste bottle.

Содержание ST-200 aQua





























































































Результаты поиска

Содержание ST-200 aQua

Отзывы:

Бренды по названию

Популярные бренды

Sensa Core ST-200 aQua, Руководство оператора

Результаты поиска

Содержание ST-200 aQua

Отзывы:

Бренды по названию

Популярные бренды