background image

ENGLISH 6/8

(1)

The threshold value depends on the type of RTD:

T

= 8 °C, T

= 9 °C, T

= 5 °C and T

= 5 ° C

PT100

PT500

PT1000

NI100

DIP-Switch settings

In the following tables:
The symbol

corresponds to DIP-Switch = 1 (ON).

Ç

No indication correspond to DIP-switch = 0 (OFF)

Ç

ON

1

Ç

OFF

0

È

DIP-Switch SW1

You must set the DIP-switches with the module powered down and without

generation of electrostatic discharges, otherwise the module may be damaged.

1 2 Baud rate

3 4 5

6

7

8 Address

9

Not Used

9600 Baud

Address and communications

parameters from EEPROM

Ç

Always leave to

OFF

È

È

position

Ç

19200 Baud

Ç

Fixed Address 01

È

Ç

Fixed Address 02

Ç Ç

Fixed Address 03

10

TERMINATION RS485

Ç

38400 Baud

Ç

Fixed Address 04

Ç

Line terminator
inserted

X

X

X

X

X

X

Fixed Address, as from binary
representation

Ç Ç

57600 Baud

È

No line termination

Ç Ç Ç Ç Ç Ç

Fixed Address 63

Filter Setting

The filtering methods can be set for every channel.
The filter consists of two independent low-pass filters:
-Filter FIR, in moving average, able to increase the noise rejection from the mains power line
and to reduce measuring noise.
-Filter IIR exponential, with programmable time constant, able to dampen fluctuations.
If an input variation is higher than threshold , then both filters are forced to quickly adapt to

T

the new value, stabilising it only later on. The filter is set with the three least significant bits of
registers MODBUS 40037..40 (refer to section

).

MODBUS REGISTERS

The following is a table containing all filter types. Propagation time (90%), that is the
maximum time between the step variation of the input and the variation of the number
which represents it in the Modbus register, including the interrogation time of an individual
register (at 115 kbaud) is indicated for each filter.
The times shown are for 50 Hz setting (for 60 Hz, you can divide by 1.2).

SET

ADC SAMPLING

FILTER

PROP. TIME 90%

Value

Bit ADC

Frequency

Type

< T

(1)

> T

(1)

000

13 bit

48 Hz

Not Present

45 ms

45ms

001

13 bit

20 Hz

Average

236 ms

103ms

010 (Default)

14 bit

11 Hz

Average

405 ms

179ms

011

14 bit

11 Hz

Media+Exp

1 s

179ms

100

14 bit

11 Hz

Media+Exp

3 s

179ms

101

14 bit

11 Hz

Media+Exp

8 s

179ms

110

14 bit

11 Hz

Media+Exp

24 s

179ms

111

14 bit

11 Hz

Media+Exp

72 s

179ms

MI00441

-3

-E

N

Содержание Z-4RTD2









Отзывы: