Sena HelloDevice Pro PS110 Скачать руководство пользователя страница 82

Страница: 82 / 109

ForwDatagrams :

Specifies the number of datagrams forwarded.

InUnknownProtos :

Specifies the number of locally addressed datagrams received successfully but discarded

because of an unknown or unsupported protocol.

InDiscard :

Specifies the number of input IP datagrams for which no problem s were encountered to prevent

their continued processing, but which were discarded (for example, for lack of buffer space). This

counter does not include any datagrams discarded while awaiting reassembly.

InDelivers :

Specifies the number of received datagrams delivered.

OutRequests :

Specifies the number of outgoing datagrams that an IP is requested to transmit. This number

does not include forwarded datagrams.

OutDiscards :

Specifies the number of transmitted datagrams discarded. These are datagrams for which no

problems were encountered to prevent their transmission to their destination, but which were

discarded (for example, for lack of buffer space.) This counter would include datagrams counted

in Datagrams Forwarded if any such packets met this (discretionary) discard criterion.

OutNoRoutes :

Specifies the number of datagrams for which no route could be found to transmit them to the

destination IP address. These datagrams were discarded. This counter includes any packets

counted in Datagrams Forwarded that meet this “no route” criterion.

ReasmTimeout :

Specifies the amount of time allowed for all pieces of a fragmented datagram to arrive. If all

pieces do not arrive within this time, the datagram is discarded.

ReasmReqds :

Specifies the number of datagrams that require reassembly.

ReasmOKs :

Specifies the number of datagrams that were successfully reassembled.

ReasmFails :

Specifies the number of datagrams that cannot be reassembled.

FragOKs :

Specifies the number of datagrams that were fragmented successfully.

FragFails :

Specifies the number of datagrams that need to be fragmented but couldn’t be because the IP

header specifies no fragmentation. For example, if the datagrams “Don’t Fragment” flag was set,

the datagram would not be fragmented. These datagrams are discarded.

Содержание HelloDevice Pro PS110














































































































Результаты поиска

Содержание HelloDevice Pro PS110

Отзывы:

Похожие инструкции для HelloDevice Pro PS110

Бренды по названию

Популярные бренды

Sena HelloDevice Pro PS110, Руководство пользователя

Результаты поиска

Содержание HelloDevice Pro PS110

Отзывы:

Похожие инструкции для HelloDevice Pro PS110

Бренды по названию

Популярные бренды