SEFRAM SF6-36V2 Скачать руководство пользователя страница 18

Страница: 18 / 20

SEQUENCER CONTROLLER

WITH OR WITHOUT

DIFFERENTIAL PRESSURE SWITCH

Technical notice

FI 72.0297.1016E

Page 18

PRECAUTIONS

If a change of fuse has to be made, replace it with a fuse of the same calibre.

Avoid dusty air entering at the pressure taps.

Take the necessary precautions to satisfy the device characteristics/data (humidity, maxi pressure, etc.).

For the 4-20mA cables, we recommend that you use shielded cable and do not follow the routing of the
power cables.

For special operating conditions : consult us.

Work interventions must always be carried out by duly qualified staff.

CALIBRATION

The device leaves our workshops, adjusted at 0, for zero pressure and at maxi for the maxi pressure value of the
range.
Settings carried out, device stabilised and at 20° C.

It is possible to adjust the zero pressure:

Put the device out-of-pressure (disconnect the pressure taps)

Place it in the pressure reading mode (using « SELECT »)

Press the « - » button and hold it down

Press the « RESET » button (keeping « - » pressed down)

Release the buttons: the zero is set

Then re-connect the pressure

SPECIFICITIES AVAILABLE ON REQUEST

−

Other supply voltage: 24/48VAC – 24VDC

−

Other DP sensor scale

Содержание SF6-36V2





















Результаты поиска

Содержание SF6-36V2

Отзывы:

Похожие инструкции для SF6-36V2

Бренды по названию

Популярные бренды

SEFRAM SF6-36V2, Руководство пользователя

Результаты поиска

Содержание SF6-36V2

Отзывы:

Похожие инструкции для SF6-36V2

Бренды по названию

Популярные бренды