Seepex BN 17-12S Скачать руководство пользователя страница 55

Страница: 55 / 86

9.2 Reassembly

A / 07.11.2019 - OM.SCT.BN.S03EN

22/36

Shear off holding band (406, 407) for material
design stainless steel, corrosion-resistant steel

Universal joint sleeve can be damaged by

hammering and striking. Joint grease

(GF)

can leak

out. Avoid hammering or striking the universal joint
sleeve.



Refer to the technical data (



chapter 3) for the

material design.



Shear off holding band

(406, 407)

below holding

band loop

(SCL)

–

Strike cutting lever

(SH)

with the palm of your

hand.



Straighten the holding band

(406, 407)

carefully

if it lifts up at the sheared-off end.

Cut off holding band (406, 407) for material
design stainless steel, heat-resistant steel

Universal joint sleeve can be damaged by

hammering and striking. Joint grease

(GF)

can leak

out. Avoid hammering or striking the universal joint
sleeve.



Refer to the technical data (



chapter 3) for the

material design.



Cut off holding band

(406, 407)

below holding

band loop

(SCL)

–

Use tool

(WBS)



File down and deburr any projecting edges.



The holding band

(406, 407)

must lie in the

groove of the universal joint sleeve

(405)



Replace the holding band

(406, 407)

if the

holding band

(406, 407)

slips back through the

loop.

Содержание BN 17-12S























































































Результаты поиска

Содержание BN 17-12S

Отзывы:

Похожие инструкции для BN 17-12S

Бренды по названию

Популярные бренды

Seepex BN 17-12S, Руководство по эксплуатации и сборке

Результаты поиска

Содержание BN 17-12S

Отзывы:

Похожие инструкции для BN 17-12S

Бренды по названию

Популярные бренды