Seepex BN 17-12S Скачать руководство пользователя страница 37

Страница: 37 / 86

9.1 Dismantling

A / 07.11.2019 - OM.SCT.BN.S03EN

4/36

9.1.3.1 Dismantle stator (601)

Dismantle dry-running protection device (TSE) (optional)

Damage to pump sided parts of the dry-

running protection device

(TSE)

during dismantling

the stator.



Before dismantling the stator, remove all pump
sided parts of the dry-running protection device

(TSE)

–

Observe the chapter Options and additional
accessories (



chapter 12.1).

WARNING

Leaking conveying medium.

Personal injury and/or material damage can occur.



Take safety precautions to protect people and the environment.



Wear suitable protective clothing.



When handling hazardous substances, comply with applicable regulations.

CAUTION

Risk of injury from moving and falling pump parts.

Body parts can get crushed.



Turn kinetic rings

(670)

only on the outer surface.



Secure lower adjusting segments

(635)

and stator half

(601)

to prevent them from falling.



Loosen adjusting screws

(639)

until kinetic rings

(670)

are flush.

Содержание BN 17-12S























































































Результаты поиска

Содержание BN 17-12S

Отзывы:

Похожие инструкции для BN 17-12S

Бренды по названию

Популярные бренды

Seepex BN 17-12S, Руководство по эксплуатации и сборке

Результаты поиска

Содержание BN 17-12S

Отзывы:

Похожие инструкции для BN 17-12S

Бренды по названию

Популярные бренды