SeeMeCNC ERIS DELTA Скачать руководство пользователя | Manualshive

Страница: 2 / 71

background image

READ ME FIRST!

READ THIS MANUAL COMPLETELY BEFORE UNPACKING AND POWERING UP YOUR
PRINTER!

Hazards and Warnings

The SeeMeCNC Eris® Delta 3D printer has motorized and heated parts. When the printer is in
operation always be aware of possible hazards.

Electric Shock Hazard

Never open the electronics bay of the printer while the printer is powered on. Before removing
the access door, always power down the printer and unplug the AC line cord.

Burn Hazard

Never touch the extruder nozzle or heater block without first turning off the hot end and allowing
it to completely cool down. The hot end can take up to twenty minutes to completely cool.
Also, never touch recently extruded plastic. The plastic can stick to your skin and cause burns.
Also before of the heated bed which can reach high temperatures capable of causing burns.

Fire Hazard

Never place flammable materials or liquids on or near the printer when powered on or in
operation. Liquid acetone and vapors are extremely flammable.

Pinch Hazard

When the printer is in operation, take care to never put your fingers in the moving parts,
including the belts, pulleys or gears. Also, tie back long hair or clothing that can get caught in
the moving parts of the printer.

Static Charge

Make sure to ground yourself before touching the printer, especially the electronics.
Electrostatic charges can damage electronic components. To ground yourself, touch a
grounded source.

Age Warning

For users under the age of 18, adult supervision is recommended. Beware of choking hazards
around small children.

2

«
1
2
3
4
...
»

Содержание ERIS DELTA








































































Отзывы:

Нет отзывов

Похожие инструкции для ERIS DELTA

Бренд: DataCard Страницы: 2

Бренд: Eazao Страницы: 50

Бренд: Oki Страницы: 104

PS100 - Photo Printer - 50 Sheets

Бренд: Olympus Страницы: 2

Бренд: Xerox Страницы: 284

imageRUNNER ADVANCE DX 717 Series

Бренд: Canon Страницы: 98

Oce VarioPrint 6000 Ultra+ Series

Бренд: Canon Страницы: 56

Бренд: Canon Страницы: 188

imageRUNNER ADVANCE C356iF III

Бренд: Canon Страницы: 96

Бренд: Canon Страницы: 218

Бренд: Infinite Peripherals Страницы: 27

Бренд: WAGO Страницы: 52

Бренд: TierTime Страницы: 89

Бренд: Dell Страницы: 128

Бренд: Dell Страницы: 4

Бренд: Dell Страницы: 4

3130cn - Color Laser Printer

Бренд: Dell Страницы: 4

Бренд: Dell Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды