ENFORCER Fingerprint Reader and Keypad
28
SECO-LARM U.S.A., Inc.
Unit fails to accept a new fingerprint
•
Ensure the User ID assigned is between 1 and 1000
•
Ensure the User ID has not been assigned to another user
Unit fails to accept a new user code
•
Ensure the User ID assigned is between 1001 and 3000
•
Ensure the user code is between 4~6 digits long and not already
assigned to another user
Unit fails to read a programmed
fingerprint
•
Ensure the finger being presented is the same finger that was
originally programmed
•
Press the finger evenly on the central area of the reader
•
Ensure the reader window is clean
Unit fails to respond to a programmed
fingerprint or user code
•
Ensure the unit is in standby mode by pressing the
key until the
LED becomes steady red
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: [email protected]
®
PICSN8
MI_SK-2612-SFSQ_190807.docx
Troubleshooting:
NOTICE:
The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2019 SECO-LARM U.S.A., Inc. All
rights reserved.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for one (1) year from the date of sale to the original customer. SECO LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO
LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO LARM’s option. In
no event shall SECO LARM be liable for any special, collateral, incidental, or consequential personal or property damage of
any kind to the purchaser or anyone else.
IMPORTANT:
Users and installers of this product are responsible for ensuring that the installation and configuration of this
product complies with all national, state, and local laws and codes related to locking and egress devices. SECO-LARM will
not be held responsible for the use of this product in violation of any current laws or codes.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
requirements and void user’s authority to operate the device.
IMPORTANT WARNING:
For a weather-resistant installation, ensure that the unit is properly sealed where the housing
base meets the wall. Incorrect mounting may lead to exposure to rain or moisture in the enclosure which could cause a
dangerous electric shock, damage the device, and void the warranty. Users and installers are responsible for ensuring that
this product is properly installed and sealed.
