background image

32

ENFORCER Access Control Keypad with Proximity Card Reader

SECO-LARM U.S.A., Inc.

FCC COMPLIANCE STATEMENT 

FCC ID: K4E1131SPQ

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO 

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT 

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s 

authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements no change to the antenna or the device 

is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements 

and voice user’s authority.

LIMITED LIFETIME WARRANTY:

 

This SECO-LARM product is warranted against defects in material and workman

-

ship while used in normal service for the lifetime of the product. SECO-LARM’s obligation is limited to the repair or replace

-

ment of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is 

caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or ab-

normal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating 

properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the 

purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall 

SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the 

purchaser or anyone else. This limited lifetime warranty is for products sold and installed in the United States and Canada. 

For all other countries the warranty is 1 (one) year.

NOTICE:

 The information and specifications printed in this manual are current at the time of publication. However, the 

SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to 

change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

Copyright © 2016 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or 

in part, without the written permission of SECO-LARM.

SECO-LARM

®

 

U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Website: www.seco-larm.com

PIHAK1

Phone: (949) 261-2999  |  (800) 662-0800 Email: [email protected]

MI_SK-1131-SPQ_160816.indd

Notes:

Also Available:

Proximity Cards

  

(sold in packs of 10)

Proximity Keyfobs

(sold in packs of 10)

PR-K1S1-A

PR-K1K1-AQ

Содержание SLI ENFORCER SK-1131-SPQ

































Отзывы: