The essentials
If the wheel bolt is very tight, carefully push
on the end of the wheel wrench with your
foot. Hold on to the vehicle for support and
take care not to slip during this operation.
Loosening wheel bolts
●
Fit the wheel wrench on as far as it will go
.
●
Hold the wrench at the end and rotate the
bolt approximately
one
turn anticlock-
wise
.
The caps protect the wheel bolts and should
be pushed fully on again after changing the
tyre.
Loosening the anti-theft wheel bolt
●
Take the adapter for the anti-theft wheel
bolts out of the vehicle tool kit.
●
Insert the adapter fully onto the anti-theft
wheel bolt
●
Fit the wheel wrench as far as it will go over
the adapter.
●
Hold the wrench at the end and rotate the
bolt approximately
one
turn anticlock-
wise
.
The
anti-theft wheel bolt
has a different
cap. This cap only fits on anti-theft locking
bolts and is not for use with standard wheel
bolts.
Important information about wheel bolts
Factory-fitted rims and wheel bolts are spe-
cially matched during construction. There-
fore, if different rims are fitted, the correct
wheel bolts with the right length and heads
must be used. This ensures that wheels are
fitted securely and that the brake system
functions correctly.
In certain circumstances, you should not even
use wheel bolts from vehicles of the same
model.
In wheels with full hubcaps, the anti-theft
locking bolt must be threaded onto positions
2
or
3
, taking the tyre valve’s po-
sition as reference
1
. Otherwise it will not be
possible to mount the hubcap.
Raising the vehicle
Fig. 74
Jack position points.
Fig. 75
Fitting the jack.
●
Place the jack* (vehicle tools) on firm
ground. If necessary use a large, strong
board or similar support. If the surface is slip-
pery (for example tiles) place the jack on a
rubber mat or similar to prevent it from slip-
ping
›››
.
●
Find the support point on the strut (sunken
area) closest to the wheel to be changed
›››
●
Turn the jack* crank handle, located below
the strut support point, to raise it until the
tab
1
is below the housing provi-
ded.
●
Align the jack* so that tab
1
“grips” onto
the housing provided on the strut and the mo-
bile base
2
is resting on the ground. The
base plate
2
should fall vertically with re-
spect to the support point
1
.
●
Continue turning the jack* until the wheel is
slightly lifted off the ground.
»
55
Содержание Arona 2018
