Sears CRAFTSMAN 944.621574 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 36

background image

4

ASSEMBLY

OPERATOR’S POSITION (See Fig. 1)

When right or left hand is mentioned in this manual, it
means when you are in the operating position (standing
behind tiller handles).

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard
wrench sizes are listed.

(1) Utility knife

(1) Wire cutter

(1) Screwdriver

(1) Tire pressure gauge

(1) Pair of pliers

(1) 9/16" wrench

FRONT

OPERATOR’S
POSITION

LEFT

RIGHT

FIG. 1

Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.

(1) Carriage Bolt

3/8-16 UNC x 1 Gr. 5

(1) Center Locknut

3/8-16 UNC

(2) Handle Lock

(1) Hairpin Clip

(1) Cable Clip

(1) Handle Lock Lever

(1) Flat Washer 13/32 x 1 x 11 Ga.

CONTENTS OF HARDWARE PACK

(1) Pivot Bolt
3/8-16 UNC Grade 5

(2) Shear Pins & Clips

«
...
2
3
4
5
6
...
»

Содержание CRAFTSMAN 944.621574





































Отзывы:

Нет отзывов

Похожие инструкции для CRAFTSMAN 944.621574

Бренд: York Страницы: 4

Бренд: CyberChill Страницы: 12

Бренд: Flora Best Страницы: 78

Бренд: FTS Страницы: 66

Бренд: York Страницы: 80

Бренд: S&A Страницы: 34

Бренд: Daikin Страницы: 30

Бренд: Elemental Solutions Страницы: 4

Бренд: Sterling Страницы: 43

Бренд: Trane Страницы: 86

Бренд: Delta Страницы: 6

Trailblazer AGZ030-101E

Бренд: Daikin Страницы: 124

MultiPower CHA 1048-P

Бренд: Clint Страницы: 36

Бренд: Carrier Страницы: 28

Бренд: Scheppach Страницы: 124

Бренд: EarthWise Страницы: 42

Бренд: Daikin Страницы: 20

Бренд: Homelite Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды