Sears CRAFTSMAN 944.621574 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 36

background image

16

SERVICE AND ADJUSTMENTS

FIG. 24

CABLE CLIP
SCREW

DRIVE
CONTROL
CABLE

EXTENSION
SPRING

ENGINE
PULLEY

IDLER
PULLEY

TRANS MIS SION
PULLEY

LESS
TEN SION

5/8"

MORE
TEN SION

TO REPLACE GROUND DRIVE BELT
(See Figs. 23 and 24)

• Remove belt guard as described in “TO REMOVE BELT

GUARD”.

• Remove old belt by slipping off engine pulley fi rst then

remove from transmission pulley.

• Place new belt in groove of transmission pulley and

into engine pulley. BELT MUST BE IN GROOVE ON
TOP OF IDLER PULLEY. NOTE POSITION OF BELT
TO GUIDES.

•      Check belt adjustment as described below.
•      Replace belt guard.
•     Reposition wheel and replace clevis pin and hairpin

clip.

GROUND DRIVE BELT ADJUSTMENT
(See Fig. 24)

For proper belt tension, the extension spring should have
about 5/8 inch (16 mm) stretch when drive control bar is
in “EN GAGED” position. This tension can be attained as
fol lows:
• Loosen cable clip screw securing the drive control

cable.

• Slide cable forward for less tension and rearward for

more tension until about 5/8 inch (16 mm) stretch is
obtained while the drive control bar is engaged.

• Tighten cable clip screw securely.

«
...
14
15
16
17
18
...
»

Содержание CRAFTSMAN 944.621574





































Отзывы:

Нет отзывов

Похожие инструкции для CRAFTSMAN 944.621574

YCAL0043E Series

Бренд: York Страницы: 184

Бренд: Racing Страницы: 24

Бренд: Cobra Страницы: 16

Бренд: AAON Страницы: 64

Бренд: Across International Страницы: 18

Бренд: Johnson Controls Страницы: 24

Бренд: Ventrac Страницы: 29

Aroace WFC-SC10

Бренд: Yazaki Страницы: 24

QTC4 STYLE A Series

Бренд: Quantech Страницы: 164

Бренд: Kasco Страницы: 14

Бренд: Garland Страницы: 172

Бренд: Haskris Страницы: 56

AGRI EASE BE-TXG Series

Бренд: BE Ag & Industrial Страницы: 12

York YCAL0041-0071

Бренд: Johnson Controls Страницы: 5

Бренд: Eurosystems Страницы: 5

Бренд: Troy-Bilt Страницы: 32

Бренд: Troy-Bilt Страницы: 44

Бренд: ryan Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды